JAI EL-2800M-PMCL User Manual Download Page 33

Page: 33 / 87

EL-2800M-PMCL / EL-2800C-PMCL

- 31 -

Table – 17 Exposure mode

Exposure Mode

Trigger Control

Trigger OFF

Trigger ON

Frame Start

Behavior

OFF

OFF or ON

Self-running
No exposure
control

Timed (EPS)
Timed(RCT)
Timed (PIV)

OFF

Self-running
Exposure control
available

Operate in EPS,
RCT or PIV

Trigger Width

OFF

Self-running
No exposure
control

Exposure control
by trigger width

Frame Start trigger: Sets whether the start of the frame is controlled externally or not.

Trigger Mode ON: If Acquisition Active is active and Exposure Mode chooses Timed or

Trigger Width, the exposure will be started by using the signal set
in Frame Trigger as the trigger.

Trigger Mode OFF: If Acquisition Active is active, the camera operates in free-running mode.

Exposure Mode can be selected from the following.
OFF:

No shutter control

Timed:

The exposure will be set in advance. The setting can be done in μsec
units.
Frame Start OFF: Free-running mode and exposure control is available.
Frame Start ON: EPS operation mode

In this status, if RCT or PIV is selected in Trigger option, the camera will
operate in RCT or PIV mode.

Trigger Width : The exposure will be controlled by the width of the trigger pulse.

Frame Start OFF: Not active. No exposure control

Frame Start ON: PWC operation mode

7.2.2 Exposure Time

This command is effective only when Exposure Mode is set to Timed. It is for setting

exposure time.

The setting step for exposure time is 1

sec per step.

Minimum:

10 μ sec

Maximum:

8 seconds

7.2.3 Exposure Auto

This is a function to control the exposure automatically. It is effective only for Timed.

ALC Reference controls the brightness.

There are three modes, OFF, Once and Continuous.

OFF:

No exposure control

Once:

Exposure adjusts when the function is set, then remains at that setting

Continuous:

Exposure continues to be adjusted automatically

In this mode, the following settings are available.

Summary of Contents for EL-2800M-PMCL
























































































Search results

Summary of Contents for EL-2800M-PMCL

Reviews:

Related manuals for EL-2800M-PMCL

Brands by name

Popular brands

JAI EL-2800M-PMCL, User Manual

Search results

Summary of Contents for EL-2800M-PMCL

Reviews:

Related manuals for EL-2800M-PMCL

Brands by name

Popular brands