background image

 

BM-500GE / BB-500GE

 

 
 

10 

4.

 

Locations and Functions 

4.1

 

Locations and functions 

 

 

 

 

  Lens mount 

 

C-mount (Note *1)

 

 

  CCD sensor 

 

2/3 inch CCD sensor 

  12-pin connector  

 

DC +12V power and GPIO interface  

  D-sub 9 pin connector   

Auxiliary GPIO interface (LVDS IN and TTL IN/OUT) 

  RJ-45  

GigE Vision I/F. Accepts connector w thumbscrews. 

  LED  

 

 

GigE Network condition: LINK 

  LED 

 

 

GigE Network condition: ACT 

  Holes for RJ-45 thumbscrews 

Vertical type (above and below RJ-45).  

  Holes for RJ-45 thumbscrews 

Horizontal type (left and right of RJ-45) (Note *2) 

  Mounting holes 

 

M3 depth 5 mm for tripod mount plate (Note *3)   

 
*1) Note:    Rear protrusion on C-mount lens must be less than 10.0mm.    
*2) Note:    When an RJ-45 cable with thumbscrews is connected to the camera, please do 

not excessively tighten screws by using a screw driver. The RJ-45 receptacle on 
the camera might be damaged.  
For security, the strength to tighten screws is less than 0.291 Newton meter 
(Nm). Tightening by hand is sufficient in order to achieve this. 

*3) Note:    The tripod adapter plate MP-41 can be used with BM/BB-500GE 

Fig. 1. Locations  

LINK

ACT.

DCIN/ TRIG

GP

IO

POWER/ TRIG

GigE

⑧ ⑨

Summary of Contents for BM-500 GE





















Reviews: