Jacuzzi Maxi Alimia, Installation Manual

Page: 37 / 136

37
- You can use the diverter to adjust the flow of water to a set of
nozzles, with respect to the other set, in inverse proportion. That
is, by turning the knob one way or the other, the force of the jets
will increase in one set of nozzles and decrease in the other
CAUTION
Do not adjust the diverter(s) when the pump is
running.
ACTIVATION OF BLOWER (air compressor)
The MaxiJacuzzi ® is provided with air jets located in nozzles
positioned as illustrated in previously .
The system conveys the air to the jets, thus forming bubbles,
which travel up through the water and expand until they reach
the surface where they burst, also creating a pleasant visual
effect.
Press the “Blower” key to start the air compressor.
The blower can be activated either in conjunction with, or
separately from, the hydromassage pumps. When the system is
started, however, the blower is always off, as are the hydro-
massage pumps.
The blower stays on for 20 minutes. It can be shut off before
that by pressing the key again.
If you want to use the blowers for aroma therapy, insert the
perfume cartridge in the compartment located under the cover
(see the chapter "Aromatherapy".
NOTES
- Activating the blower and the hydromassage pumps at the
same time may turn the heater off, if it is on.
- When the blower is started, the filtering pump is also turned
on, if it was not already. It will remain on for 10 minutes after
the function is turned off.
UNDERWATER SPOTLIGHT
This spotlight is turned on using the key located on control panel:
Press the “Light” key to turn on the spotlight located on
the wall of the tub.
The spotlight stays on for 2 hours. It can be shut off before
that by pressing the key again.
NOTE: when you turn on the spotlight, the filtering pump is al-
so turned on, as there is probably someone in the tub. It stays
on for 10 minutes after the spotlight is turned off.
Utility functions
CONTROL PANEL LOCK
There are two modes for this function:
- Partial lock: this makes it impossible to programme the filtering
cycle or change the water heating set point. You also cannot acti-
vate the energy savings mode (Econo) or rapid filtering (“Instant
Clear”).
All other control panel keys remain active.
- Total lock: this mode prevents operation.
Partial lock
To activate this function:
Press and hold the “Econo” key for a few seconds. The
symbol for the locked panel will flash on the display ( ). Con-
tinue holding the key until the message “LocP” appears and the
symbol stays on steady, which indicates that the lock has been
activated.
If you press a key whose use is not permitted, the display will
show the message “LocP" for five seconds.
Total lock
To activate this function:
Press and hold the “Econo” key. The symbol for the
locked panel will flash on the display ( ). Continue holding
the key even after the message “LocP” appears, until the mes-
sage “LocF” appears. The function is now active.
If you press any key, the display will show the message
“LocF" for 5 seconds.
De-activating the lock
In both modes, to de-activate the lock , press and hold the “E-
cono” key until the message “LocP” or “LocF” disap-
pears and is replaced by the message “ULoc” .
NOTES
- If their is a power outage, the keyboard lock (either partial
or total) is removed.
- If you want to change from partial lock to total lock (or vice-
versa), you must first deactivate the current lock and then set
the new lock mode.
TEMPORARY SYSTEM SHUTDOWN
(“STANDBY”)
This function lets you suspend operation of all system devices for
a period of
60 minutes (this value cannot be changed) so that
you can perform routine maintenance without having to discon-
nect the power supply.
WARNING
If you need to access the electrical parts, parts
that are normally powered, or the rotating parts