background image

Contents

1

Important:  Read complete instructions before beginning installation.

Each whirlpool bath arrives ready for installation, completely equipped with motor/pump assembly and plumbing and
fittings necessary for whirlpool operation.  The drain/overflow kit and faucet kit must be installed on the bath by the
installer.

Remove the bath from the carton.  Retain the shipping carton until satisfactory inspection of the product has been
made.  Do not lift the bath by the plumbing at any time; handle by the shell or frame only.

Immediately upon receipt, inspect the shell and walls before installing.  Should inspection reveal any damage or defect
in the finish, do not install the bath.  Damage or defect to the finish claimed after the bath is installed is excluded from
the warranty.  Jacuzzi Whirlpool Bath's responsibility for shipping damage ceases upon delivery of the products in good
order to the carrier.  Refer any claims for damage to the carrier.  For definitions of warranty coverage and limitations,
refer to the warranty information.

All bath units are factory tested for proper operation and watertight connections prior to shipping.  Note:  Prior to final
installation, the bath must be filled with water and operated to check for leaks that may have resulted from
shipping damage or mishandling.
  Jacuzzi Whirlpool Bath is not responsible for any defect that could have been
discovered, repaired, or avoided by following this inspection and testing procedure.

Specifications _______________________________________________________________________

2

Hardware ___________________________________________________________________________

3

Framing and Support _________________________________________________________________

4

Rough-in Reference __________________________________________________________________

5-7

Skirt Installation and Service Access _____________________________________________________

8-9

Electrical ___________________________________________________________________________

9

Drain Information and Plumbing _________________________________________________________

9

Water Supply ________________________________________________________________________

10

Center Panel Installation _______________________________________________________________

11-12

TV Installation (For units with TV) ________________________________________________________

13

Fixed Glass Panels Installation __________________________________________________________

14-15

Side Wall Installation __________________________________________________________________

16

Caulking ___________________________________________________________________________

17-18

Sliding Doors Installation _______________________________________________________________

19

Dome Installation ____________________________________________________________________

20

Operation __________________________________________________________________________

21-23

Maintenance ________________________________________________________________________

24-26

Warranty ___________________________________________________________________________

29-30

Save These Instructions for Future Use.

Date Purchased ____________________________________________________________

Purchased From ____________________________________________________________

Installed By ________________________________________________________________

Serial Number ___________________________

Summary of Contents for J-ALLURE

































Reviews: