36
Install control access box door and reinstall the cabinet side pa-
nels.
I
In the event that not enough electricity is available, it is still possi-
ble to activate an electronic consumption limiter, operating within the
electronic control box (please refer to the wiring diagrams included
in this manual).
This operation can only be performed by authorised Jacuzzi® tech-
nicians.
Spa Fill Up Procedure
For best results, read each step in its entirety before
proceeding with this procedure.
I
Prepare The Spa For Filling
- Clear all debris from the spa. (Although the spa shell has been
polished at the factory, you may want to treat it with a specially
formulated spa cleaner.)
Consult your authorized Jacuzzi dealer for additional information
prior to filling spa.
- Remove both ProClarity™ and ProClear™ Plus skimmer, pol-
ishing filter lids and filters as illustrated in Section “Cleaning
the Filter Cartridges”.
I
Fill Spa
Place the end of your garden hose into empty skimming filter
bucket (filter bucket on your left) as you stand next to the spa.
Fill spa half way, then place the garden hose into the opposite
filter bucket (filter bucket on your right) while adding the remain-
ing fill water.
Fill until water covers all jets but does not touch the bottom of
the lowest headrest (DO NOT OVERFILL!).
CAUTION: TO DECREASE BUILD UP ON COMPONENTS
AND MINIMIZE ACRYLIC DAMAGE.
Never fill with water from a water softener. If your water is
extremely “hard,” it is preferable to fill half-way with hard water
and the rest of the way with softened water. Water that is too
soft can be corrosive to metal components.
IMPORTANT:
Always fill your spa through both filter buckets
after draining. Failure to do so may cause air to be trapped in
either pump, preventing the pump from circulating water. Remove
the hose and replace both filter cartridges as illustrated in Sec-
tion “Cleaning the Filter Cartridges”.
I
Turn on Power
- Turn the hot tub on using the relevant switch(es) (the heater and fil-
ter/circulation pump are activated automatically)
While the hot tub is turning on, a welcome message is displayed
and the blow-out cycle is then activated to remove any air in the pi-
pes.
The welcome message disappears after 3 seconds and the normal
display is shown. The control panel display varies according to the
model.
If the screen displays either a “Cool Warning” or “Freeze Pro-
tection” error, this is normal. Normally, at the initial fill, the water
tends to be cold. Refer to “Error/Display Messages” for additional
information.
I
Activate Jets Pumps
Turn on jet pumps when adding chemicals (see Section “Acti-
vating the Jets Pumps” to activate jets).
NB: do not start the pump(s) if the water does not cover the highe-
st pump nozzles.
- Open all of the air controls and turn all of the massage selector k-
nobs to the central position.
Welcome
Rev 1.0
9
9
7
8
2
3
1
5
10
11
6
12
12
P
o
w
er
on
L
amp
on
DANGER!
TURN POWER
OFF! DO NOT
LOOK AT LIT BULB
.
S
EVERE EYE
DAMAGE OR BLINDNE
SS
CAN OCCUR!
4
13
1
ProTouch™ Glass Control Panel
2
ProTouch™ Control Box
3
Heater
4
CLEARRAY Water Purification System
5
QuickDrain™
6
Jets Pump
7
Filter/Circulation Pump
8
Jets Pump
9
Power Supply Entrance(s)
10
Spa Drain Valve
11
Pump Drain Plugs(s)
12
BLUEWAVE 2.0 Wireless Stereo
13
Jacuzzi Prolink™ Remote Monitoring System
Module
Summary of Contents for J-500 Series
Page 2: ......
Page 3: ...Italiano Avvertenze 4 English Warnings 32 Fran ais Recommandations 59 Index...
Page 90: ...90...
Page 91: ...91...