Jacuzzi J-400 Series Installation Manual And Use & Maintenance Download Page 64

Page: 64 / 120

From the Settings Menu, tap

to highlight the “Heat

& Filter” menu tab in Orange. Tap

to the enter the

menu. The select one of the heating settings.

Auto heating:

When programmed to “Auto,” the spa will maintain the water
temperature to the set temperature. Heating will occur when
necessary.
To select this mode, tap (

)

next to the “Auto” icon.

Econo heating:

This is an energy saving heating program that allows the spa to
heat during non-peak hours. When programmed to “Econo,” the
spa will only be allowed to heat the water between 5:00 PM to
7:00 AM every day of the week. The hours cannot be adjusted.
To select this mode, tap (

)

next to the “Econo” icon.

Day heating:

When programmed to “Day,” the spa will only be allowed to
heat the water between 7:00 AM to 5:00 PM every day of the
week. The hours cannot be adjusted.
To select this mode, tap (

)

next to the “Day” icon.

Programming the Primary Filter

To access the “Primary Filter” feature, tap

from the “Heat &

Filter” menu, to enter the “Primary Filter” programming.

During a primary filtration, the circulation pump, CLEARRAY
and ozone unit (if applicable) are activated. The factory default
cycle starts at 12:00 AM and last for 8 hours. If you elect to keep
this setting, then you can skip this section.

몇

In extreme bitter cold weather we recommend you pro-
gram the circulation pump to run 24 hours. Refer to the
"Winterizing" section.

Any time the circulation pump runs outside of a program cycle,
e.g. for heating, that run time will be deducted from the next
primary filter cycle. For example, the primary filter cycle is set
to 8 hours every 24 hours but the circulation pump comes on
for 2 hours to heat the water after the cycle has finished. The
next primary filter cycle will only be for 6 hours not 8 hours.

To change the default cycle:

When you enter the menu, “Start” and “12” will be highlighted.
Tap

to change the hour in 1-hour increments. To

switch from “AM” to “PM” you must round a 12-Hour period.
Tap

to accept the change. Tap

to program the end

time for the cycle.
Tap

the hour block to change the end time. Tap

to change the hour in 1-hour increments. To switch from “AM”
to “PM” you must round a 12-Hour period.
Tap

to confirm and save your changes. Tap

to return to

the Heat & Filter Menu. Tap again to return to the Settings Menu.

Summer Logic:

In warm weather, the water temperature in the spa

may exceed the set temperature. This condition may occur due to
heat transference from the filter/circulation pump and jets pumps. If
the water temperature is higher than 35°C (95°F) and rises two de-
grees above the set temperature, a “Summer Logic” condition occurs
that deactivates the filter/circulation pump and CLEARRAY®. This sa-
fety feature cannot be altered! The filter/circulation pump and
CLEARRAY® will remain off until the water temperature cools to the
set temperature (except between 9am-11am when the fil-
ter/circulation pump runs for it’s mandatory 2 hour cycle.) To help
prevent a “Summer Logic” condition, it may be necessary to reduce
filter/circulation pump cycles run times in warm weather.

Programming the Secondary Filter

To access the “Secondary Filter” feature, tap

from the Heat

& Filter Menu, to enter the “Secondary Filter” programming. Du-
ring a secondary filtration, the Jets Pump 1 is activated. There
are 3 cycles you can select from. The factory default cycle is
“Away Mode.” If you elect to keep this setting, then you can skip
this section.

Indicates that the feature is active.

Indicates that the

feature is not active.

To change the Secondary Filter cycle:

Away Mode: Secondary Filtration is disabled. To activate this
mode, tap (

)

next to the “Away” icon.

Note:

This is the factory default setting.

Infrequent Mode: Activates two cycles at 8:00 PM and 8:00 AM

every other day

. Each cycle will last 10 minutes for a total of 20