4 CONTROLS
en-30
Switch Status: Displays the current switch settings, and
is used to diagnose switch problems. A status of 0
indicates the switch is in the OFF position. A status of 1
indicates the switch is in the ON position. Check the
wiring and operation of any switch that is not displaying
the correct status.
The switches are broken up into three sets of numbers,
with a gap between each set. Refer to Safety &
Operation Manual for switch references.
The first set of numbers displays the status of the left,
center, and right reel switches (C, D, and E) on the
instrument panel.
The second set of numbers displays the status of the
mow switch (B), light switch (F), horn switch (G), and
system power switch in start position (H).
The third set of numbers displays the status of the
lower and raise switches that are part of the joystick
(J), and the seat switch.
Maximum Mow Speed: To set the maximum mow
speed, press either of the orange buttons (AM or AN) on
the LDU until the set MAX MOW SPEED screen is on the
LCD display. Press the black button (AL) to enter set
mode. Use the orange buttons to raise (AN) or lower
(AM) the maximum mow speed to the desired speed.
press the black button to set speed.
Maximum mow speed must be between 1.0 and 5.0
mph (1.6 and 8.0 kph), and is adjustable in 0.5 mph
(0.8 kph) increments.
Maximum Transport Speed: To set the maximum
transport speed, press either of the orange buttons (AM
or AN) on the LDU until the set MAX SPEED screen is
on the LCD display. Press the black button (AL) to enter
set mode. Use the orange buttons to raise (AN) or lower
(AM) the maximum transport speed to the desired speed.
press the black button to set speed.
Maximum transport speed must be between 1.0 and
9 mph (1.6 and 14.5 kph), and is adjustable in 0.5
mph (0.8 kph) increments.
Number of Reel Blades: To set the number of blades on
each reel, press either of the orange buttons (AM or AN)
on the LDU until the reel blades screen is on the LCD
display. Press the black button (AL) to enter set mode.
Use the orange buttons to raise (AN) or lower (AM) the
number of reel blades. press the black button to set
speed. Entering the wrong number of blades will affect
the fixed FOC setting.The only reels currently available
are 7, 9, 11, or 15 blade reels.
2WD/3WD Mode: pressing black button (AL) toggles
mower between 2WD and 3WD modes. Do not set
mower to 3WD if the 3WD system is not installed.
Fixed FOC Setting: To set the fixed FOC, press either of
the orange buttons (AM or AN) on the LDU until the FOC
x.xxx CHANGE? screen is on the LCD display. Press the
black button (AL) to enter set mode. Use the orange
buttons to raise (AN) or lower (AM) the FOC value to the
desired setting. press the black button to set speed. The
minimum and maximum fixed FOC setting varies,
depending on the number of blades. [See Section 4.6].
15 Blade Reel ............ 0.05 - 0.25 in. (0.12 - 0.63 cm)
11 Blade Reel ............ 0.05 - 0.25 in. (0.12 - 0.63 cm)
9 Blade Reel .............. 0.06 - 0.30 in. (0.15 - 0.77 cm)
7 Blade Reel .............. 0.07 - 0.39 in. (0.19 - 0.99 cm)
Factory Reset: To reset controller to factory default
values, press either of the orange buttons (AM or AN) on
the LDU until the Factory Reset screen is on the LCD
display. Press the black button (AL) to reset values back
to factory default settings. All values saved in mower
attachment modes will also revert to their original factory
default settings.
Mower Attachment Mode 1 (11 Blade Reel)
Reel Direction ............ CW
Reel Speed ................ 2200 rpm
Mow Speed................ 4 mph
Transport Speed ........ 9 mph
FOC ........................... 0.160 in.
Reel Blades ............... 11
Display Units.............. English
Backlap Timer............ 10 Minutes
Mower Attachment Mode: To set the mower attachment
mode, press either of the orange buttons (AM or AN)
until the MODE CHANGE? screen is on the lcd display.
Press the back button (AL) to enter set mode. Press the
right orange button until the desired mode is on the
screen, then press the black button to select it. See
Section 4.5.5 for default values
.
NOTICE
If a mower attachment mode change is required,
change mower attachment mode first before setting
other values. Values stored in new mode will override
previous settings for reel speed, FOC, maximum mow
and travel speeds, reel direction, and display units.
