Jacobsen Eclipse 322 Operation Manual Download Page 103 | Manualshive

Page: 103 / 116

background image

LDU ERROR CODES 12

en-103

12.6 HYBRID ENGINE CONTROLLER ERROR CODES________________________________

Hybrid engine controller error/fault codes display on the
LDU as a two digit error code.

LDU Error Code

Description

Caution

LED

Alarm

Sounding

Engine

Stop

Traction

Stop

Mow Stop

On

Off

Yes

No

Yes

No

Yes

No

Yes

No

Pack Voltage too high. Engine speed
is set to idle. Restart mower.
Continue with normal operation.
Notify maintenance personnel at end
of shift.

4

4

4

4

4

Pack Voltage too low. Engine speed
is set to idle. Restart mower.
Continue with normal operation.
Notify maintenance personnel at end
of shift.

4

4

4

4

4

Generator temperature greater than
266° F (130° C). Engine speed is set
to idle. Restart mower. Continue with
normal operation. Notify
maintenance personnel at end of
shift.

4

4

4

4

4

Generator temperature greater than
212° F (100° C) or rectifier
temperature greater than 176° F (80°
C). Generator derates. Shut mower
down and wait ten minutes. Restart
mower. If fault returns, return mower
to maintenance shed.

4

4

4

4

4

Throttle actuator Fault. Engine
speed is set to idle/spring return.
Restart mower. If fault returns, return
mower to maintenance shed.

4

4

4

4

4

Rectifier temperature greater than
212° F (100° C) for 3 seconds.
Generator derates. Restart mower.
Continue with normal operation.
Notify maintenance personnel at end
of shift.

4

4

4

4

4

Pack voltage sensor greater than 70
VDC for 3 seconds. Engine shut
down. Restart mower and return to
maintenance shop

4

4

4

4

4

Pack voltage sensor 2VDC for 2
seconds. Engine speed set to
idle.Return mower to maintenance
shop.

4

4

4

4

4

GENERATOR

FAULT 14

GENERATOR

FAULT 15

GENERATOR

FAULT 21

GENERATOR

FAULT 22

GENERATOR

FAULT 23

GENERATOR

FAULT 31

GENERATOR

FAULT 54

GENERATOR

FAULT 55

«
...
101
102
103
104
105
...
»

Summary of Contents for Eclipse 322





















































































































Reviews:

No comments

Related manuals for Eclipse 322

Brand: Yard-Man Pages: 32

Brand: Harry Pages: 32

Brand: Ariens Pages: 33

M51-150AWR CLASSIC

Brand: McCulloch Pages: 296

Brand: Neuton Pages: 28

Commercial Front Cut Rider YHRK20

Brand: Yazoo Pages: 83

Brand: Ferris Pages: 44

EC Hydro Midsize

Brand: Ransomes Pages: 54

Brand: Troy-Bilt Pages: 40

Brand: Lastec Pages: 21

EZ Walk MW1230B

Brand: Maxim Pages: 11

Brand: Snapper Pages: 256

Brand: Earthwase Pages: 20

Brand: Racing Pages: 27

Brand: MasterCraft Pages: 15

Brand: Craftsman Pages: 26

Brand: Craftsman Pages: 44

Brand: Craftsman Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands