background image

 

 

 

SAFETY

 

 

Your new Jackson Grill barbeque is a safe, 
convenient appliance when used and 
maintained properly.  As with all gas-fired 
appliances, certain safety precautions 
must be observed.  

Failure to follow 

these precautions may result in 
damage or injury.

  If you have any 

questions or concerns regarding the 
assembly or operation of this appliance, 
you should contact your dealer, gas 
appliance technician or your gas company. 
 

NEVER OPERATE THIS BBQ WITHOUT 
THE PULL OUT MAIN DRIP TRAY IN 
PLACE.

 

 

F

OR 

Y

OUR 

S

AFETY 

 

If you smell gas: 
 
1.

 

Shut off gas to the appliance. 

 
2.

 

Extinguish any open flame. 

 
3.

 

Open lid. 

 
4.

 

If odor continues, immediately call 
your supplier or fire department. 

 
DO NOT store or use gasoline or any 
other flammable liquid in the vicinity 
of this or any other appliance. 
 
An LP Cylinder not connected for use 
shall not be stored in the vicinity of 
this or any other appliance. 

 

C

AUTION

 

 

1.

 

For outdoor use only. 

 
2.

 

If stored indoors, detach and leave 
cylinder outdoors. 

3.

 

This appliance must not be operated 
unattended. 

 
4.

 

Special care must be taken to keep 
small children away from heated 
surfaces. 

 

E

LECTRICAL 

C

AUTION 

 

1.

 

If any accessory is used on this 
appliance with an external electrical 
power source, the accessory (when 
installed) must be electrically 
grounded in accordance with local 
codes.  In the absence of local codes, 
the following standards apply: 

 

(Canada) CSA C22.1 Canadian 
Electrical Code, and (USA) ANSI/NFPA 
No. 70 – Latest Edition. 

 
2.

 

Do not cut or remove the grounding 
prong from the plug. 

 
3.

 

Keep the electrical supply cord and 
fuel supply hose away from any heater 
surface. 

 

INSTALLATION

 

 

In Canada, this appliance must be 
installed in accordance with the local code 
and relevant CGA standards: 
 

CAN/CGA-B149.1 LP Gas/Propane 
Installation Code and latest codes 
where applicable. 
In the USA, this appliance must be 
installed in accordance with the local 
code and relevant national code:  ANSI 
Z223.1 – Latest Edition National Fuel 
Gas Code. 

 
 
 

Summary of Contents for JG3













Reviews: