User instructions of JA-60 "Comfort"
- 3 -
MDY51410
5. Voice dialer programming by user
If the control panel is equipped with a 60X telephone dialer module and if enabled in the programming mode during installation, setting of
the voice and Pager dialer telephone numbers and messages can be changed in the user mode (with master code). Setting can be
performed by entering programming sequences from the keypad while in the control panel user mode (but not from the JA-60D keypad):
•
Enter the user mode (entering
F 0 Master Code
, factory default UC=1234), indicated by a „U“ on the display. This can only be done
while the panel is disarmed.
•
The parameters of the dialer can be set by entering programming sequences from the keypad. Any unfinished programming
sequence can be terminated by pressing the
N
key.
•
To exit the user mode, press the N
key („U“ will turn off).
List of the voice & Pager user programmable parameters
Function sequence
options
note
Telephone numbers for voice message
7xx..x F y
xx...x
= tel. number,
y
=
memory 1 to 4, pause = F0
Pager dialing programming
7x.xF9z..zF5
x..x
= provider tel. number
z..z
= pager
message
1:
2:
3:
4:
5:
Erase telephone number
7F0Fy
y
= memory 1 to 5, entering
7F0F0 erases all
Record voice message
8 0
Dialer testing
89
if 2 messages - 88 & 89
5.1. Telephone number entering (
sequence:
7xxx....xxFy)
Store telephone numbers for voice message entering: 7 xx... xx F y
xx...xx
-> telephone number
y
-> memory number from 1 to 4
A telephone number can have a maximum of 16 digits. A
pause
can be entered with
F0
(pause can not be entered as the first digit).
Example:
to store tel. number 02 123456 to memory no. 2 enter: 7 02 F0 12345 F2
Note: enter a pause (F0) after the last digit of a number which is calling a mobile phone. This way the number will be called only once
and the dialer will not check the line signals (some mobile phone systems do not generate standard telephone line signals).
When activated, the dialer will
disengage all other devices hooked up to the phone line (telephone, fax..). It will then, one by one,
call and play the user recorded message, for all programmed numbers. If the dialer makes a successful connection to a programmed
number, it will not call that number again. If the number is busy, the dialer will make 3 more attempts to call it.
Empty tel. number memories are skipped. If all memories are empty, the dialer is completely disabled.
To delete a telephone number
enter:
7 F0 F
y
y
->
memory number from 1 to 4
entering
7 F0 F0
will erase all tel. numbers, including the Pager number
Store number to call Pager
(to memory number 5) entering:
7 xx..x F9 zzz....zz F5
xx...x
-> provider prefix
F9
-> separator (it will wait for a provider’s signal and will switch to DTMF if not used)
zzz...zz
-> pager number and numeric message and other specific codes (language selectors, end of
message etc.) if requested by the Paging provider
F5
-> to store the number to memory no. 5
As a maximum 32 digits can be stored to memory number 5. Special characters can be entered with the following Fx codes:
F0
->
pause
F7
->
*
F8
->
#
Example:
enter 7 0611 F9 1 1234 555 F80 F5 if the provider prefix is 0611, the Pager number 1234 and the message 555. Number 1
after F9 is a language selector, code F80 represents
# 0
# 0
# 0
# 0
= end of message.
Note: some Paging providers also offer an option to send the message as an
SMS to the GSM network
. Consult your Paging provider
for details if you have trouble sending a message to the Pager.
To delete the Pager number
enter:
7 F0 F5
If the memory number 5 is empty, no message will be sent to a Pager.
