background image

10

/16

System Operation Manual - IZIP E3 Twn:exp

03/10/14

Basics

IMPORTANT:

 The IZIP owner’s manual included with your bike contains most of the 

important safety and usage information about this bike, which is not included in this system 

operation manual. Be sure to read the owner’s manual before you begin riding or working 

on your bike.

Battery charging

You should charge the battery fully before 

riding for the first time, following the instructions 

below. Be sure to check the section of your 

owner’s manual discussing “Battery care & 

safety” for additional information.

Charging procedure

Connect the power cord to the battery 

charger. Plug the charging plug into the 

battery’s charging port, then plug the wall 

plug into a wall outlet.

The charger should always be plugged 

first into the battery, then into the wall 

outlet.

Charging will begin immediately. The 

charger’s LED indicator will light up to show 

its status.

LED

STATUS

Red

Charging

Green

Finished charging

Red 

(flashing)

Charging error; see 

“Charging issues” below

If the battery is attached to the bicycle, 

and the bicycle is turned on, the battery level 

indicator on the bike’s display will show the 

current charge level. See “Turning the bike 

on and off” on page 11.

The battery does not have a “memory”. This 

means that it can be charged at any time, or 

partially charged, without causing damage 

or decreasing performance.

Charge time

The amount of time needed to charge the 

battery varies based on the battery’s charge 

level. A completely empty battery will take 

between 4 and 6 hours to charge. A battery 

at 50% may only need 2-3 hours to come 
to a full charge.

Checking the battery’s charge 

level

Before riding, you should check the 

battery’s charge level. If the battery is not 

fully charged, riding range will be reduced.

To check the battery’s charge level, first 

install the battery in the bike, then turn the 

bike on (see “Using the battery” on page 

11). The battery level indicator on the 

display will show the battery’s charge level. 

Each bar represents about 20% capacity:

BARS 

BATTERY CHARGE

(low battery 

warning)

<5%

1

≤20%

2 ~20– 40%

3 ~40 – 60%

4 ~60 – 80%

5 ~80 – 100%

Summary of Contents for E3 Twn:exp

















Reviews: