iWave i.MX6 SODIMM Hardware User'S Manual Download Page 15

Page: 15 / 56

REL 1.2

Page 15 of 56

i.MX6 SODIMM SOM Hardware User Guide

iWave Systems Technologies Pvt. Ltd.

2.4

PMIC

i.MX6 SODIMM SOM supports NXP

’s

PF0100 PMIC for On-SOM power management. The PF0100 is a Power

Management Integrated Circuit (PMIC) designed specifically for always ON application with the NXP i.MX6

application processors.

This PMIC supports up to six buck converters, six linear regulators, RTC supply and coin-cell charger with

programmable output voltage, sequence and timing. i.MX6

CPU’s I2C

1 interface is used for PMIC programmable. I2C

address for PMIC is 0x08.

2.5

Memory

2.5.1

DDR3 SDRAM

i.MX6 SODIMM SOM by default supports 1GB DDR3 RAM memory in 64bit mode. To support this, it uses four 256MB

DDR3 SDRAM ICs. These devices operate at 1.5V voltage level. Each pair of DDR3 ICs is physically located on either

side of the iMX6 SODIMM SOM. The RAM size can be expandable up to maximum of 4GB.

Note: By default, 512MB DDR3 with 32bit mode only supported in i.MX6 Solo CPU based SODIMM SOM.

2.5.2

SPI NOR Flash

The i.MX6 SODIMM SOM supports 2MB SPI NOR Flash as default boot device. This is connected to eCSPI1 controller

of the i.MX6 CPU and operates at 3.3 Voltage level. The SPI flash memory is physically located on top side of the

SODIMM SOM. The memory size of the SPI Flash can be expandable.

2.5.3

eMMC Flash

i.MX6 SODIMM SOM supports 4GB eMMC (expandable) memory as mass. eMMC is directly connected to the

uSDHC4 of the i.MX6 CPU and operating at 3.3V Voltage level. The eMMC flash memory is physically located on

bottom side of the SODIMM SOM. The memory size of the eMMC Flash can be expandable.

Summary of Contents for i.MX6 SODIMM

























































Search results

Summary of Contents for i.MX6 SODIMM

Reviews:

Related manuals for i.MX6 SODIMM

Brands by name

Popular brands

iWave i.MX6 SODIMM, Hardware User'S Manual

Search results

Summary of Contents for i.MX6 SODIMM

Reviews:

Related manuals for i.MX6 SODIMM

Brands by name

Popular brands