![background image](http://html1.mh-extra.com/html/ivt/hpc-1400/hpc-1400_manual_2097831015.webp)
15
Instruction manual
EN
before using it, make sure the cable is not damaged or worn out.
If the cable is not in good condition, do not use the appliance;
take it to an authorized service centre.
When tool is used outdoor, only use an extension cable that
•
is suitable for outdoor use and which is marked for this specific
use. Keep it away from the working area, from damp, wet or oily
surfaces and away from heat and flammable materials.
Avoid any accidental starting: make sure that the power
•
switch (if present) is in the «off» position, before plugging the
tool in.
Remove adjusting keys or wrenches before turning the tool
•
on.
Do not use the tool if the switch does not turn the tool on
•
or off. Any tool that cannot be controlled with the switch is
dangerous and must be repaired.
WARNING
During the use of power tools, some dust containing chemicals
known to cause cancer, may occur. Some of these chemicals are:
lead from lead based paints, crystalline silica from bricks and
cement and other masonry products, arsenic and chromium
from chemically treated lumber and other dangerous products. If
dust is present, your risk from these exposures varies, depending
on how often you do this type of work.
To reduce your exposure
to these chemicals, any time you do pulverulent operations,
work in a well ventilated area and work with approved safety
equipment, such as dust masks that are specially designed to
filter out microscopic particles.
If the appliance strikes a foreign body, examine the device
•
for signs of damage and carry out any necessary repairs before
restarting and continuing to work.
If the appliance starts to vibrate abnormally, turn it off
•
and check for the cause immediately. Vibration is generally a
warning of trouble.
Always switch off the appliance and wait until the device
•
completely stops whenever you leave the machine, before
carrying out maintenance, before checking, cleaning or working
on the appliance.
It is forbidden to move or modify any of the internal parts
•
of the device.
Specific safety rules
Connecting to power source
Devices of the Protection Class IP 1 shall be con nected only
•
to properly grounded power sources.
The device must be grounded. If an extension cord is used
•
while operating the high pressure device, the cross-section shall
be as fol lows:
1.5 mm at max for length 20 m
2.5 mm at max for length 50 m
Pursuant to safety rules the extension cord to be used must
•
have a ground wire connected via the plug to the main circuit
ground.
To ensure safety of the appliance use only original spare
•
parts from the manufacturer or approved by the manufacturer.
If the device’s cable must be replaced, use only a power
•
cable provided by the manufacturer.
Use a strain relief device with extension cords to relieve
•
tension.
If the power or extension cord couplings are replaced, their
•
water-resistance and mechanics integrity must be preserved.
Always protect electrical parts of the device against water
•
jet.
Connecting to the water supply
Always comply with the requirements of local water
•
company. According to DIN 1998 standard requirements,
pressure washers may only be connected to the main drinking
water supply if a backflow preventer valve is installed in the
supply hose of the appliance.
All hose connection threads must be watertight.
•
Damaged high-pressure hoses must not be used due to
•
blowout danger. Replace damaged hoses immediately. Use only
hoses and couplers provided by the manufacturer.
Do not run the washer without water. This will cause
•
damage to it.
Using the device
Before using the device check it and its accessories for
•
proper condition and operating safety. A faulty device must not
be used.
This appliance has been designed for use in combination
•
with cleaning agents recommended by the manufacturer. Under
no circumstances use solvent-containing liquids or undiluted
acids/solvents! Such liquids include petrol, paint thinners and
fuel oil. In aerosol these liquids are highly inflammable, explosive
and toxic. In addition, acetone and undiluted acids or solvents
can cause damage to device components.
Should the device be operated in dangerous areas (e.g., at
•
filling stations), proper safety prescriptions are to be observed.
Any use of the device at the explosive hazard facilities is strictly
forbidden.
Position the device on solid surface.
•
All conductive parts in the work area must be splash
•
protected in all directions.
Do not lock the pistol grip lever when operating in the
•
«On»
position.
Always wear protective clothing and safety glasses as loose
•
particles and other debris may be propelled at high speed by
the water jet.
Under no circumstances should high-pressure water stream
•
be directed towards people, animals, the device itself or its
electric parts.
To prevent high-pressure stream from damaging tires and
•
valve stems, a distance of at least 30 cm must be maintained
during cleaning. The first sign of tire damage is its color
alteration. Damaged tires and valve stems pose death risk.
Do not clean asbestos-filled materials or other hazardous
•
materials with water stream.
Operation
The device must never be left unattended while the motor
•
is running.
Summary of Contents for HPC-1400
