Service menu
AirModule –6 720 813 268(2014/10)
47
Heating control mode
• In
Outside temperature compensation control mode
only summer
mode, setback mode (depending on the selected type of setback)
and adjustment of the outside temperature (by reduced heating
requirements due to good insulation) can result in shutdown of the
heating circuit pump.
– Room adjustment can be set in the
Adjusting the heating curve
menu. Room adjustment influences the two outside temperature
controlled operating modes. Room influence is only available if a
room controller is installed in a suitable reference room.
–
Outdoor-temp.-compensated
(optimised heating curve,
standard setting)
Used mainly for radiators and underfloor heating system.
–
Outside temp. with low end
:
Simple heating curve, page 49.
Used mainly for fan convectors.
Setting the heating system and the heating curves for outside
temperature compensated control
▶ Setting the heating type (radiator, convector or underfloor heating)
in the
Set heating/cooling
>
Circuit 1
menu
... 4
Setting .
▶ Setting the control mode (outside temperature controlled or outside
temperature controlled with a base point) in the
Control type
menu.
The items not relevant to the selected heating system and the
selected operating mode are hidden. The settings only apply to the
selected heating circuit.
Menu for setting the heating curve
Outside temperature compensated (optimised heating curve)
The heating curve provides an economic and convenient operation of
the heating system with outside temperature compensated control. The
operating system will based on the settings automatically calculate the
best possible heating curve. This results in a curve that is slightly bent to
Heating switch-on delay
1 ...
4
... 48 h
Heating start delay
Room temperature
changeover diff.
– 5 ...
2
... 5 K
If the measured room temperature is above the set room temperature by the value set here, the cooling
mode is activated (e.g. at 2 K: set room temperature = 23 °C, measured room temperature = 25 °C –
cooling is activated)
Dew point temp. diff.
2 ...
5
... 10 K
Determines the safety distance to the calculated dew point. The flow set temperature is thereby above the
calculated dew point by at least the value set here.
Min. set flow value
10 ...
10
... 35 °C
If a humidity sensor is installed for the heating/cooling circuit: the lowest set flow temperature value.
10 ...
17
... 35 °C
If no humidity sensor is installed for the heating/cooling circuit: the lowest set flow temperature value.
Mixer
Yes
Selected heating/cooling circuit is with mixing valve
No
Selected heating/cooling circuit is without mixing valve
Mixer runtime
Selected heating/cooling circuit mixing valve operating time
Shown in standard display
Yes
Selected heating/cooling circuit is show in the standard display.
No
Selected heating/cooling circuit is not show in the standard display.
Menu Item
Setting range
Description
Table 30 Settings in the Heating/cooling circuit 1 to 4 menu
NOTICE:
System damage!
If the approved operating temperature for plastic pipes
(secondary circuit) are disregarded, parts of the system
can get damaged.
▶ Do not exceed approved set values.
Menu Item
Setting range
Description
Design temperature
(Flow temperature at lowest
outside temperature)
or
End point
T
0
30 ...
60
... 85 °C
(radiator)
30 ...
45
... 60 °C
(underfloor heating system/
convector)
The system temperature only applies during outside temperature compensated control without base
point. The system temperature is the flow temperature that is reached at the lowest outside temperature
and will therefore influence the slope of the heating curve.
The end point only applies during outside temperature compensated control with base point. The end
point is the flow temperature that is reached at the lowest outside temperature and will therefore
influence the slope of the heating curve. When the base point has been set to a value above 30°C the base
point is the minimum value.
Low end
(Flow temperature at an air
temperature of 20 °C)
e.g. 20 –
25 °C
... End point The heating curve base point only applies during outside temperature compensated control with simple
heating curve.
Max. flow temperature
T
0 max
30 ...
75
... 85 °C
(radiator)
30 ...
48
... 60 °C
(underfloor heating system/
convector)
Maximum flow temperature
– 5 ... – 1 K
Sunshine will to a certain extent influence outside temperature compensated control (the solar thermal
energy decreases the required heat output).
Off
The control does not take sunshine into consideration.
Room influence
Off
The outside temperature compensated control will operate independently from the room temperature.
1 ...
3
...10 K
Room temperature deviation equivalent to the setting is adjusted by a parallel offset of the heating curve
(only if a room controller is installed in a suitable reference room). The higher the setting value, the greater
is the max. room temperature influence on the heating curve.
Room temperature offset
– 10 ...
0
... 10 K
Parallel offset of the heating curve (e.g. if the room temperature measured by a thermometer deviates
from the selected set value)
Table 31 Heating curve settings menu
