background image

 

-

 Before going to

 Mode 6

 please make sure that the “Known 

load weight” is ready to be lifted.                                                        

The loaded forks must be on the ground 

                                                                               

(No hydraulic pressure in the lifting hydraulic circuit)

 

- Press the

 “M”

 button to advance to

 Mode 6 

and immediately lift the 

“Known load weight” just above the ground. 

 

- LED display will go blank and within few seconds LED display 
will show the value of calibrated “Known load weight of 4000”           

                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                      

 

 Lower the load to the ground. 

                                                             

System will go automatically into  operational mode.                         
System is ready to be used.               

                                                                                  

Mode digit will display number 

8. 

                                                                                                        

Note:

 If system is set up for overload alert the

 Mode 7 

will be shown automatically when loaded forks  are 

lowered to ground. Follow instruction for overload alert value input.

 

        

                                                                                               

Weighing calibration function is completed 

Lower the loaded forks to the ground.  

Integrated Visual Data Technology Inc.,   3439 Whilabout Terrace, Oakville, Ontario, Canada  L6L 0A7

    

Summary of Contents for SkidWeigh Classic










Reviews: