background image

Electrical power short circuit protection  

                                                                                                            

- All of the SC SkidWeigh systems are internally short circuit protected with resettable fuse. There is no 
need to    install external inline fuse in orange wire connected to the ignition switch. 
- Automotive 60 V load dump protection                                                                                                                       

-Reversal power supply protection  

“Quick test to determine if electrical connections are done right”                                      

Note: This  procedure is only to test if electrical connections of the system installation into the vehicle is 
done properly.                                                                                                                                                                       
After you have connected electrical power and pressure transducer cable you can “quickly” check the 
system operation. 

 - Lower the forks to the ground                                                                                                                                           
- Turn On ignition switch                                                                                                                                                     
- Digital LED display will be activated, showing software version and serial number                                                            
- Number 8 will be shown on LED display above the Mode sign.                                        
- Lift forks with any load just above the ground. Mode number 

8

 will go off for few seconds and some load 

weight will be shown on the LED display.                                                                                                                                       

- If the above test is valid then the system electrical connections are done right.                                         

The next procedure will be to calibrate the SkidWeigh weighing function.                                                                                                            

Use paper clip to access buttons “M” and “Arrow Up”  

-

Lift truck equipped with hydraulic accumulator 

                                                                   

If the standard SkidWeigh system is installed on the lift trucks equipped with hydraulic accumulators, 
please contact us to provide you with different digital indicator having specific software algorithm to 

obtain load weight accuracy /- 1% of vehicle maximum lifting capacity.                                                                                                                                                                  

                      

 

Fully automatic weighing calibration procedure 

  

        

                                                                                                                                                

The SC SkidWeigh calibration is automatic and is done by lifting empty and loaded forks with known calibration load 
weight just above the ground. 

MAKE SURE THAT YOU HAVE A KNOWN LOAD WEIGHT AND KEEP IT NEARBY 

TO COMPLETE THE CALIBRATION

.                                                                                                                                                                             

For the best results use at least minimum calibration load test weight  of 40 to 60% of maximum lifting capacity of 
the lift truck. Use customer floor scale or find a known skid load weight within the operational facility.                                                                                                                                                                         

Integrated Visual Data Technology Inc.,   3439 Whilabout Terrace, Oakville, Ontario, Canada  L6L 0A7

    

Summary of Contents for SkidWeigh Classic










Reviews: