manualshive.com logo in svg

ITW Simco ION IQ Easy LP, Installation And Operating Instructions Manual, Page: 4 / 20

Share
Download
ITW Simco ION IQ Easy LP Installation And Operating Instructions Manual Download Page 4

2

5201223 Rev. J

IQ Easy Speed-T & Hybrid-T
Static Neutralizing Bars

CAUTION – 

The emitters are sharp and can cause physical injury. 

ATTENTION – 

Les émetteurs sont pointues et peuvent causer des blessures. 

NOTE – 

The high-voltage emitters (9 kV) are limited to a current of 50 uA, 

which means that they are electrically safe to touch and shockproof. 

NOTE – 

IQ Easy bars are designed to neutralize electrostatically charged 

surfaces only. 

NOTE – 

During the ionization process a small amount of ozone is produced. 

The ozone concentration around the electrodes depends on a large number 

of factors, such as the amount of space around the static neutralizing bar and 

the air circulation. This means that no general value can be specified for the 

ozone concentration. For installations with poor ventilation it may be 

necessary to take precautions to ensure safe values of ozone concentration.

NOTE – 

If changes, adjustments etc. are made without prior written consent 

or if repairs are performed using non-original parts, the equipment's 

warranty will no longer be valid. 

Summary of Contents for Simco ION IQ Easy LP





















Reviews:

No comments