manualshive.com logo in svg

ITW Simco ION IQ Easy LP, Installation And Operating Instructions Manual, Page: 17 / 20

Share
Download
ITW Simco ION IQ Easy LP Installation And Operating Instructions Manual Download Page 17

15

5201223 Rev. J

IQ Easy Speed-T & Hybrid-T
Static Neutralizing Bars

6. MAINTENANCE

WARNING – 

Remove power before working on IQ Easy Bars. 

AVERTISSEMENT – 

Débranchez l'alimentation électrique avant toute 

intervention sur l'appareil. 

Regular Cleaning

Clean the emitter points and the static neutralizing bar regularly with a stiff bristle, 

non-metallic brush. 

WARNING – 

The emitters are sharp and can cause physical injury. 

AVERTISSEMENT – 

Les émetteurs sont pointues et peuvent causer des 

blessures. 

Removing Heavy Soil

Clean the static neutralizing bar using isopropyl alcohol. Be sure to allow the static 

bar to dry completely before applying power.

Calibrate Bar

NOTE – 

Calibration should be performed when the system is first installed 

and may be performed after the static bar has been cleaned and the system 

verified as operating correctly.

If the system is new, it may be necessary to perform an initial calibration.  The initial 

calibration sets the relative nominal ion output for the system.  Calibration should 

only be performed on IQ Easy Static Neutralizing Bars that are new or just cleaned 

and known to be in proper working order.
During calibration the target to be neutralized (web, film, etc.) may remain in place, 

but MUST NOT BE MOVING.  If the web is moving past the static bar (e.g. the 

machine is in operation) the calibration will be faulty.
The system should be “on” and in the operating mode.  On the IQ Power Control 

Station tap on the device icon for the IQ Easy static bar.  Tap on the Neutralizer 

tab.  Tap on the page forward arrow to get to the last page.  Find the IQ Easy Bar 

Calibration line and tap on the pencil.  Enter the Control Station password at the 

prompt (Note: the factory default password is “PASSWORD”.)  Tap on “yes” at 

“Calibrate IQ Easy Bar?”.
During calibration the system output will be cycled and the indicator lights on 

the static bar end will flash.  Calibration takes as long as 5 seconds. The indicated 

ionization output will be high (90% to 100%).
The calibration data is stored in non-volatile memory in the IQ Easy bar and used 

on subsequent power ups.

Summary of Contents for Simco ION IQ Easy LP





















Reviews:

No comments