ITW Dynatec DYNAMINI Operation And Service Manual Download

Page: 45 / 90

Page 7-8

Revised 1/05

ITW Dynatec c. 2004

DYNAMINI ASU Manual #20-25

Problem

Possible Cause

Solution

Display for Hose (or

Head) = EO1

Display for Hose (or

Head) = EO2

1. No Hose (or Head) is

connected.

2. Disconnection between

ASU and Hose (or be-

tween Head and Hose).

3. Disconnection at X4 on

PCB.

4. Hose (or Head) sensor is

inoperative.

1. Hose (or Head) sensor

short circuit.

2. Short circuit in plug con-

nection between ASU

and Hose (or between

Hose and Head).

3. Inoperative PCB.

1. Connect Hose (or Head) if need-

ed. If not needed, ignore display.

2. Check plug connection.

3. Make proper connection.

4. Check resistance and compare to

resistance table.

a. For head: if sensor is

inoperative, replace sensor.

b. For hose: if sensor is

inoperative, replace hose.

1. Check resistance and compare to

resistance table.

a. For head: if sensor is

inoperative, replace sensor.

b. For hose: if sensor is

inoperative, replace hose.

2. Make proper connection.

3. Replace PCB.

Plug

Sensor

Heater

Sensor &

Heater

ASU Socket

Hose Plug

Summary of Contents for DYNAMINI



























































































Search results

Summary of Contents for DYNAMINI

Reviews:

Related manuals for DYNAMINI

Brands by name

Popular brands

ITW Dynatec DYNAMINI, Operation And Service Manual

Search results

Summary of Contents for DYNAMINI

Reviews:

Related manuals for DYNAMINI

Brands by name

Popular brands