ITW Dynatec DYNAMINI Operation And Service Manual Download

Page: 37 / 90

ITW Dynatec c. 2004

DYNAMINI ASU Manual #20-25

Page 6-3

Revised 1/05

Flushing the System

Contaminated adhesive, accumulation of residue, or changing the adhesive formulation may require
the system to be flushed. At least 6 liters (1.5 gallons) of flushing fluid is required (PN L15653).

1. Pump out as much of the molten adhesive as possible.

2. Reduce the pump pressure to zero by first turning the pump switch to OFF. Then open the

purge screw, following the instructions given in “Purging the Filter Manifold of Adhesive
and Pressure” on page 6-2.

3. Disconnect one of the supply hoses’ adhesive feed from its applicator head. Do not

disconnect electrical power to the head. Put the hose in a secured position within a container
to catch the used flushing fluid.

4. Add flushing fluid to the hopper and allow approximately fifteen minutes for it to reach

hopper temperature. Carefully stir the flushing fluid to mix with any remaining adhesive.

For Piston Pumps:

Slowly turn the air pressure regulator clockwise.

For Gear Pumps:

Slowly turn the pressure relief control valve clockwise.

6. Pump about half of the fluid into the container.

For Piston Pumps:

Turn the regulator counter-clockwise.

For Gear Pumps:

Turn the motor OFF.

8. Remove the output filter and replace the basket. Install a new o-ring on the filter nut

(lubricate the new o-ring with o-ring lubricant prior to installation) and tighten the brass nut.

9. Add new adhesive to the hopper and heat to application temperature.

10.

For Piston Pumps:

Slowly turn the air pressure regulator clockwise.

For Gear Pumps:

Turn the motor ON.

11. Actuate each applicator until all flushing fluid is removed and a steady stream of new

adhesive flows.

12.

For Piston Pumps:

Re-adjust the pump air pressure for desired flow.

For Gear Pumps:

Re-adjust the pressure relief for desired flow.

13. Re-fill the hopper and resume production.

WARNING

The flushing fluid will splash easily. Wear protective clothing, gloves and

goggles to prevent severe burns.

Pressure

Relief Valve

Pressure

Regulator

Summary of Contents for DYNAMINI



























































































Search results

Summary of Contents for DYNAMINI

Reviews:

Related manuals for DYNAMINI

Brands by name

Popular brands

ITW Dynatec DYNAMINI, Operation And Service Manual

Search results

Summary of Contents for DYNAMINI

Reviews:

Related manuals for DYNAMINI

Brands by name

Popular brands