ITC DOSTEC-AC Page 30 Original Manual Download

Page: 30 / 60

Analog output value (mA)

External pulse output value (pulse/min)

Level sensor alarm output

Alarm output

Ventilation output

Analogue input value (mA)

External pulse input value (Hz)

Pressure sensor input value (BAR/PSI)

External pulse input value (ON-OFF)

Remote activation input

Number of strokes per minute

Flow detector input value

INPUTS

OUTPUTS

0/4-20mA

101

144

Pulse Hz

Press Bar 4.5

Pulse x:y

Remote

St/min

Pulse Flow

0/4-20mA 12

Pulses/min 101

Level Relay OFF

Alarm Relay ON

Vent OFF

4.4.2 Counters

Strokes (st)

Dose volume according to the current setup (l/h or GPH)

Total operating time (hours)

Short circuit alars

Overload alarms

Over temperature alarms

Press to reset strokes and volume counters
or to not.

4.4.3 Info Unit

ENT

ESC

Serial number

Ratep pump flow (l/h or GPH)
Maximum pressure (BAR or PSI)

Strokes/min

Hardware version

Firmware version

ENT

MONITOR

REAL TIME

COUNTERS

INFO UNIT

ENT

RESET COUNTERS

ENT.. = YES

ESC.. = NO

COUNTERS

ENT

MONITOR

REAL TIME

INFO UNIT

COUNTERS

ENT

INFO UNIT

Strokes 290

Volume 101

T. hour 000

Short. circ. 00

Overload 00

Overtemp 00

Serial N. 1000

Flow l/h 0240

Stk/min

144

19,0

4204

3.01

Press Bar

Hard Vers.

Soft Vers.

l / h

0 0 0

MODE

0240

l / h

0 0 0

MODE

0240

Motor Starting Voltage

Motor Frequency Factor

Maximum Current

Motor Acceleration

Voltage Retention

Calibration Factor

Stroke Volume

INFO UNIT

Start Volt

V/F Factor

Max Curr.

Accel

Volt LF

K Calib

SVol ml

040

025

080

028

106

07,230

Summary of Contents for DOSTEC-AC





























































Search results

Summary of Contents for DOSTEC-AC

Reviews:

Related manuals for DOSTEC-AC

Brands by name

Popular brands

ITC DOSTEC-AC, Original Manual

Search results

Summary of Contents for DOSTEC-AC

Reviews:

Related manuals for DOSTEC-AC

Brands by name

Popular brands