ITC DOSmart AC F30-D50 Page 27 Manual Download

Page: 27 / 48

Operation

Auto:

If the pump has a pressure sensor connected, by selecting this option the pump will keep the flow

unchanged even if the working pressure changes.

Manual (MAN):

If the pump does not have a pressure sensor, but the working pressure is constant, the

pressure value can be entered manually so that the pump adjusts to the nominal flow value.

With no compensation (OFF):

The pump flow will be as shown in the curves on page 8.

DOSING PUMP
Flow

Flow max

Limit

Pres. Alm

Pres. Comp

12.5

l/h

Bar

25.0

100

05.0

Off

5.2.3.2 Units

Select the units for flow, pressure and proportionality

ENT

CONFIGURATION

SET UP

IN / OUT

PUMP CALIBRATION

DOSING MODE

SET UP

DOSING PUMP

FLOWMETER

LOCK CODE

UNITS

MODBUS

UNITS

Flow

Pressure BAR

Proportional

LITERS

UNITS

Flow

Pressure

Proportional

LITERS

BAR

UNITS

Flow GALONS

Pressure PSI

Proportional

ppm

l / h

0 0 0

MODE

25.0

Change litre/gallons by pressing

and confirm by

pressing

ENT

Change bar/psi units by pressing

and validate by

pressing

ENT

Change %/ppm units by pressing

and validate by

pressing

ENT

Change by pressing

and confirm by pressing

ENT

Create Flow

[email protected]
www.createflow.cz

Distribuce Create Flow

tel: +420 722 712 652

Summary of Contents for DOSmart AC F30-D50

















































Search results

Summary of Contents for DOSmart AC F30-D50

Reviews:

Related manuals for DOSmart AC F30-D50

Brands by name

Popular brands

ITC DOSmart AC F30-D50, Manual

Search results

Summary of Contents for DOSmart AC F30-D50

Reviews:

Related manuals for DOSmart AC F30-D50

Brands by name

Popular brands