Isokern Magnum 86072-60 Installation, Operation And Owner'S Manual Download Page 50

Page: 50 / 56

Common Chimney Terminations

Two chimney terminations are offered by Isokern, the DM

large crown cap and the DM small crown caps. These are cement crown

caps designed to provide a weather cap to the DM chimney system.

Their design is typical of the cement caps found on traditional masonry

chimneys.

Due to owner preference and architectural design criteria other

chimney terminations can be used alone or in conjunction with the crown

caps. Special design caps may be designed and constructed by others

and must be fashioned so as not to restrict the flow of smoke and gasses

out the top of the flue opening. Figure 105 depicts common chimney

terminations.

Check with local building codes to establish the need for

chimney caps and spark arrestors or for any limitations to their design

and use.

FIGURE 105

Summary of Contents for Magnum 86072-60

























































Search results

Summary of Contents for Magnum 86072-60

Reviews:

Brands by name

Popular brands

Isokern Magnum 86072-60, Installation, Operation And Owner'S Manual

Search results

Summary of Contents for Magnum 86072-60

Reviews:

Brands by name

Popular brands