manualshive.com logo in svg

Isokern Magnum 86072-60, Installation, Operation And Owner'S Manual

Share
Download
Isokern Magnum 86072-60 Installation, Operation And Owner'S Manual Download Page 28

Non-Combustible

Material

1 1/2”

MIN

1 1/2” MI

N

1 1/2”

MIN

Hearth Extension

33

” mi

n

12” 

min

12” 

min

Insulation Behind sheathing 

with 1 1/2” Clearance

When Supported

3” min When 

Unsupported

1 1/2”

min

1 1/2”

NOT PERMITTED

9”

MIN

Do Not Place Sheathing 

WIthin the 1 1/2” Required 

Clearance to Combustibles

28

Clearance to Insulation & Vapor Barriers

The Magnum 86072 Series firebox backwall, side walls and the smoke dome back require 1 1/2” clearance. (Figure 66) 

Keep all insulation, vapor barriers, “house wrap” paper and other insulating type membranes and products, including 

fiberglass, cellulose and other insulation, (anything that carries an “R” rating) a minimum of three inches (3”) away from 

all firebox and chimney surfaces. 

Exception:

 

If insulation is used in walls surrounding the fireplace, insulation may be installed behind sheathing of gypsom board, 

plywood, particle board or other material on the side facing the Isokern. The facing material cannot be within 1 1/2” to the fireplace 

sidewalls.

If insulation or vapor barriers are used in walls surrounding the Magnum 86072 Series fireplace, it is strongly recommended that the 

walls be sheathed with gypsum board, plywood, particle board or other material on the side facing the Isokern. Unsecured insulation 

and vapor barriers must be placed a minimum of 3” away from the unit.

FIGURE 66

FIGURE 67

Summary of Contents for Magnum 86072-60

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands