manualshive.com logo in svg

Isokern Magnum 86072-60, Installation, Operation And Owner'S Manual

Share
Download
Isokern Magnum 86072-60 Installation, Operation And Owner'S Manual Download Page 34

34

 

 

The Magnum 86072 fireplace is not rated for installation 

on  a  combustible  floor  system.  Engineered  drawings  for  a  Fire-

Lite installation on a combustible floor can be obtained bey calling 

800-642-2920.  Magnum  86072  Series  fireplaces  must  be  built 

upon a concrete support slab with no wood underpinnings. Proper 

reinforced concrete support slab for Magnum 86072 installations 

may include the following types:

1. Slab on grade: standard residential, minimum four inch (4”) thick, 

2500 psi concrete foundations on properly compacted fill. This type 

foundation can support Isokern installations up to thirty feet (30’) 

overall height (brickledge installations not included). (Figure 76).

 

2.Slab-on-grade foundations, thickened and reinforced: for 

additional 

load carrying. (Figure 77)

3. Off-grade slab on foundation walls and footings.

 

Projects with off-grade floor systems as well as upper story 

installations require this type of support. (Figure 78)

 

When building off-grade support slabs the code required 

hearth extension substrate should be built as a continuation of the 

support slab for the Magnum 86072 unit. (Figure 78)

 

Supports for off grade slabs must be concrete or steel and 

capable of supporting the slab, Isokern unit and the chimney.

 

For multi-floor and back-to-back installations proper

weight computation on an individual basis is required. Consult local 

structural engineer for load bearing requirements.

Important:  

Foundations and footings must meet local code and 

be approved by the local building authority. For any foundation 

design and load requirements check with local structural engineer. 

It is the responsibility of the General contractor to insure adequate 

foundations.

Magnum 86072 Series fireplace weights and “foot print” areas:

The  total  fireplace  weight  for  each  Magnum  86072  model  listed 

below includes: Magnum 86072unit pumice parts only:

A. Model Magnum 86072 - 60: 2952 lbs. @ 73.5”x 28” = 14.29 

sq.ft.

B. Model Magnum 86072 - 72: 2652 lbs. @  83.5”x 28” = 16.63 

sf.ft.

Totals are exclusive of any chimney components. See page 36 for 

Isokern DM chimney component weights.

 

“Footprint” areas listed above are base plate dimensions 

for each model and are exclusive of code required hearth extension 

areas. See page 32 for hearth extension dimensions.

Note:

 Additional support slab area may be required at the side or 

back of the Magnum 86072 unit to provide bearing for structural 

supports to a DM offset chimney sequence.  (See pages 40-42 for 

offset chimney support requirements.)

Concrete Support

FIGURE 77

FIGURE 76

FIGURE 78

Summary of Contents for Magnum 86072-60

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands