iSMA iSMA-B-W0202 User Manual Download Page 5

Page: 5 / 41

iSMA-B-W0202 User Manual

www.ismacontrolli.com

DMP263en | 1st Issue rev. 3 | 05/2022

page 5 of 41

•

1.1 Revision History

Rev.

Date

Description

1.0

28 Apr 2015

First edition

1.1

29 Dec 2016

New HVAC functions Heating and Cooling based on output

thermostatic control with a setpoint and differential value

setting;

Added new input mode Time Relay NC [ms], Time Relay

NO and NC in seconds, Input Forwarding;

Added new input mode: Ordinary IO, Monostable Relay,

Bistable Relay, Time Relay NO and NC [ms], Time Relay NO

and NC in seconds, Input Forwarding, Heating, Cooling with

corresponding Modbus registers;

Added reset output to default after input mode change;

Added power Led flashing after I/O watchdog triggered;

Changed I/O watchdog reset after read/write registers

through USB;

Added immediately detecting sensors short circuit and

disconnection regardless of filter settings on universal

inputs.

1.2

17 Dec 2018

Added watchdog functionality for the Radio, if the radio does not

receive the correct packet for 180 seconds, the radio module will

restart.

1.3

25 May 2022

Rebranded

Table 1. Revision history

Summary of Contents for iSMA-B-W0202










































Search results

Summary of Contents for iSMA-B-W0202

Reviews:

Related manuals for iSMA-B-W0202

Brands by name

Popular brands

iSMA iSMA-B-W0202, User Manual

Search results

Summary of Contents for iSMA-B-W0202

Reviews:

Related manuals for iSMA-B-W0202

Brands by name

Popular brands