iSMA iSMA-B-W0202 User Manual Download Page 24 | Manualshive

Page: 24 / 41

background image

iSMA-B-W0202 User Manual

www.ismacontrolli.com

DMP263en | 1st Issue rev. 3 | 05/2022

page 24 of 41

Register

Device

40249

Radio AESKEY D1-D0

40250

Radio AESKEY D3-D2

40251

Radio AESKEY D5-D4

40252

Radio AESKEY D7-D6

40253

Radio AESKEY D9-D8

40254

Radio AESKEY D11-D10

40255

Radio AESKEY D13-D12

40256

Radio AESKEY D15-D14

Table 14. Radio AESKEY registers

7.2.5 Radio Received Frames Counter (40257)

The 32-bit register contains the number of valid messages received by the module via

radio protocol from last power up. The register value is reset after a power cycle or after

changing transmission parameters (baud rate, stop bits, parity, etc.).

7.2.6 Radio ERROR Frames Counter (40259)

The 32-bit register contains the number of error messages received by the module via

radio from last power up. The value is reset after a power cycle or after changing

transmission parameters (baud rate, stop bits, parity, etc.).

7.2.7 Radio Transmitted Frames Counter (40261)

The 32-bit register contains the number of transmitted messages by the module via radio

from last power up. The value is reset after power cycle or after changing transmission

parameters (baud rate, stop bits, parity, etc.).

7.2.8 Wireless Device Status (40263-40390)

The register contains information about the signal strength of the other W0202 modules

operating on the same channel. Each device has its own register for status indication.
The device number equals the Modbus address of this device.

Register

Device

40263

WIRELESS DEVICE STATUS 1

40264

WIRELESS DEVICE STATUS 2

40265

WIRELESS DEVICE STATUS 3

«
...
22
23
24
25
26
...
»

Summary of Contents for iSMA-B-W0202










































Reviews:

No comments

Related manuals for iSMA-B-W0202

Brand: FAAC Pages: 32

Brand: IBM Pages: 38

Brand: M-Audio Pages: 26

Brand: M Climate Pages: 12

Brand: Zamel Pages: 2

Brand: Zamel Pages: 2

Brand: Zamel Pages: 2

Brand: Watts Pages: 24

Brand: µ-Dimension Pages: 48

Brand: µ-Dimension Pages: 2

Bell & Gossett Technologic PPS

Brand: Xylem Pages: 20

Brand: Toro Pages: 2

Brand: Aqua Lung Pages: 24

M-DUINO PLUS series

Brand: Industrial Shields Pages: 46

Brand: Eaton Pages: 2

Brand: Audioplex Pages: 1

XBee DigiMesh 2.4

Brand: Digi Pages: 157

Brand: Instrutech Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands