iSMA iSMA-B-W0202 User Manual Download Page 19 | Manualshive

Page: 19 / 41

background image

iSMA-B-W0202 User Manual

www.ismacontrolli.com

DMP263en | 1st Issue rev. 3 | 05/2022

page 19 of 41

7.1.6 Device Actions (40001)

Setting the 40001 register according to the table below enables 1 of 3 available actions:

reset module, reload settings, and set to default.

Value

Type of Action

0x01FF

Reset of device

0x02FF

Reload settings (RS485, Radio)

0x03FF

Set device to default

Table 4. Device actions

7.1.7 Modbus Protocol Type (40134)

The register contains parameters, which define the Modbus protocol type (RTU or ASCII).

Value

Protocol Type

0 (default)

Modbus RTU

1

Modbus ASCII

Table 5. The Modbus Protocol Type register

7.1.8 Modbus Address (40135)

The register contains information about the Modbus address of the module. The default

address is 1.

7.1.9 Baud Rate (40136)

The register contains information about the baud rate.
Particular register value determines the baud rate in accordance with the table below.

Value

Baud Rate

0

1200

1

2400

2

4800

3

9600

4

19200

5

38400

6

57600

«
...
17
18
19
20
21
...
»

Summary of Contents for iSMA-B-W0202










































Reviews:

No comments

Related manuals for iSMA-B-W0202

Brand: zipwake Pages: 12

Brand: Watts Pages: 2

Brand: jbc Pages: 12

Brand: Samson Pages: 92

Brand: Jafar Pages: 10

Ecomot300 AC2630

Brand: IFM Electronic Pages: 111

PXI-6683 Series

Brand: National Instruments Pages: 4

Brand: National Instruments Pages: 9

Brand: National Instruments Pages: 11

Brand: National Instruments Pages: 29

Brand: National Instruments Pages: 11

Brand: National Instruments Pages: 7

FIELDPOINT FP-1600

Brand: National Instruments Pages: 21

FieldPoint FP-1001

Brand: National Instruments Pages: 65

FieldPoint FP-1001

Brand: National Instruments Pages: 19

Brand: National Instruments Pages: 16

Brand: National Instruments Pages: 10

Spartan-3A DSP FPGA Series

Brand: Xilinx Pages: 140

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands