Iseki SF310 Operator'S Manual Download Page 79

Page: 79 / 92

CHAPTER 10. TROUBLESHOOTING

2. BRAKE SYSTEM

3. LIFT SYSTEM

Troubles

Presumable causes

Remedies

• Exhaust fumes are black.

• Clogged exhaust system

• Excessive fuel injection rate

• Insufficient injection nozzle pressure

• Incorrect injection timing

• Check muffler for clogging and

clean it.

• Consult your dealer.

• Engine stalls at low speed.

• Defective injection pump

• Defective injection nozzles

• Incorrect valve clearance

• Consult your dealer.

• Engine races.

• Clogged governor

• Engine oil leaks into cylinder.

• Consult your dealer.

• Excessive fuel consumption

• Defective fuel

• Clogged air-intake line

• Engine is overloaded.

• Fuel leaks

• Incorrect valve clearances

• Use proper fuel.

• Clean air cleaner and air-intake

hose inside.

• Raise cutting height or slow down

front mower.

• Replace damaged parts with new

ones and tighten joints securely.

• Consult your dealer.

• Charge lamp is blinking.

• Defective wiring

• Lower electrolyte level

• Loose fan belt

• Defective alternator

• Defective regulator

• Correct loose, dirty, short, improp-

erly earthed terminals.

• Replenish with distilled water to

upper limit.

• Tighten it properly.

• Consult your dealer.

• Defective braking effect or

uneven braking

• Excessive master brake pedal play

• Worn brake linings

• Improperly adjusted brake rods

• Correct pedal play.

• Consult your dealer.

• Correct rod length.

• Master brake pedal does not

return smoothly.

• Fatigued or broken return spring

• Defective lubrication of linkage

• Replace it.

• Lubricate lubrication points.

• Lift does not rise.

• Low transmission oil level

• Air trapped inside hydraulic piping

• Fill up to upper limit.

• Consult your dealer.

Summary of Contents for SF310





























































































Search results

Summary of Contents for SF310

Reviews:

Iseki SF310, Operator'S Manual, Page: 79 / 92

Search results

Summary of Contents for SF310

Reviews: