manualshive.com logo in svg

Iseki SF310, Operator'S Manual, Page: 40 / 92

Share
Download
Iseki SF310 Operator'S Manual Download Page 40

38

SF310,370

3.7. PARKING BRAKE LEVER (Except G type)

While depressing the master brake pedal fully, move the 
lever rearward and the parking brake is applied. To 
release the parking brake, depress the master brake 
pedal again.

 

IMPORTANT:  

 Never start travelling with the parking 
brake applied, or the brake performance 
will deteriorate soon or, even worse, the 
brake system could break down.

CAUTION: When leaving the front mower, be 
sure to apply the parking brake.

4. FENDER (WING) PANEL

4.1. TRANSMISSION RANGE SHIFT LEVER

This lever shifts the transmission range into HIGH and  
LOW speed ranges.

: 

LOW:

   Shift the lever forward, and the transmission 

is shifted to the low speed range.

: 

HIGH:

   Shift the lever rearward, and the transmission 

is shifted to the high speed range.

N

: 

NEUTRAL:

   The transmission is at the neutral posi-

tion.

IMPORTANT:  

 Before shifting the range shift lever, be sure 
to stop the front mower from travelling.

4.2. LIFT LEVER

With this lever, the lift link (mower deck) is raised or low-
ered.

:   

DOWN:

 Shift the lever forward to this mark, the lift is 

lowered.

:   

UP:

 Shift the lever rearward to this mark, the lift is 

raised.

CAUTION: When servicing or leaving the 
front mower, be sure to lower the mower deck 
to the ground.

IMPORTANT:  

 Do not hold the lift lever too long in the  
UP position(

), or it may damage the 

hydraulic system.

LIFT LOCK:

 The lift cylinder is equipped with a lift locking 

device.

WARNING: Be sure to raise the lift to its upper-
most position and engage the lift lock when 
servicing the mower deck.

IMPORTANT:  

 Use the lift lock when servicing only with 
the mower deck raised. Do not use when 
travelling or transporting by truck, or it 
may damage itself and hydraulic system.

(1)   Transmission range shift lever
(2)   Lift lever
(3)   Cruise control lever

Released

Locked

A:   Hydraulic cylinder
B:   Lift lock
C:   Lift link

1

2

3

FIG. 41

FIG. 43

FIG. 42

Summary of Contents for SF310





























































































Reviews:

No comments