manualshive.com logo in svg

Iseki SF310, Operator'S Manual, Page: 72 / 92

Share
Download
Iseki SF310 Operator'S Manual Download Page 72

SF310,370

70

33. PERIODICAL INSPECTION TABLE

:Inspection, replenishment, and adjustment 

:Cleaning and washing

:Replacement 

:Consult your dealer. 

Check points

Engine oil

Air cleaner

Engine coolant

Fuel

Fuel strainer

Fan belt

Electrolyte level

Engine oil filter

Transmission oil

Transmission oil filter

Suction filter

Master brake pedal play

Tire pressure

Reduction gear case 

oil

Wheel tightening bolts

Grease-up

Radiator screen

Radiator

Electrical apparatus

Safety switches

Air intake openings

Bolts and nuts

Rubber pipes

Pre-

operation

Inspection and servicing intervals

hours of operation

50

100

150

200

250

300

350

400

Intervals

after that

Replace after initial 50 hr

and then every 150 hr.

Clean after every 50hr.

Replace every 2 year.

Clean after every 100hr. 

Replace element after every 

300hr or once a year. 

Inspect after every 50hr.

Replace after initial 50hr.

Replace after every 300hr.

Replace after initial 50hr.

Replace after every 300hr..

Replace after initial 50hr.

Replace after every 300hr.

Replace after initial 50hr.

Clean after every 200hr.

Inject grease after every 50hr.

Adjust after every 300hr.

Check after every 100hr.

Judgement

criteria

Maintain the specified level.

Maintain the specified level.

Keep fuel tank always full.

There should be no dust or

water in filter.

10mm (0.4 in.) deflection

Maintain the specified level

Maintain the specified level.

20 to 30 mm (0.8 to 1.2in.)

Front: 1.4 kgf / cm2

Rear: 1.6 / 1.5 (wide) kgf / cm2

There should be no loose.

There should be no clogging.

Engine hood and rear 

cover

There should be no clogging.

There should be no clogging.

All should work properly.

All should work properly.

There should be no clogging

There should be no loose ones.

Ref.

page

49

60

53

52

65

52

53

54

58

61

50

61

62

62

55

59

Replace after initial 50hr.

and then every 300hr.

Maintain the specified level.

50

63

Rear axle oil

Replace after initial 50hr.

and then every 600hr.

Maintain the specified level.

51

64

64

Steering wheel

Inspect after every 300hr.

There should be no

abnormality.

59

57

Toe-in

0 to 10 mm (0 to 0.4 in. )

60

68

65

65

66

67

64

—

—

IMPORTANT:
•  

 Above mentioned service intervals should be regard as reference creteria. If working conditions are harder, earlier 
service is recommended.

•  When special technique or special tools is required, consult your dealers.

Summary of Contents for SF310





























































































Reviews:

No comments