Iseki SF310 Operator'S Manual Download Page 77

Page: 77 / 92

CHAPTER 10. TROUBLESHOOTING

1. ENGINE

CHAPTER 10. TROUBLESHOOTING

Troubles

• Starter motor does not work.

• Starter motor works but

engine does not start.

• Engine runs at irregular

speeds or stalls soon.

• Engine knocks.

Presumable causes

• Master brake pedal is not depressed.

• PTO switch is not in OFF (

) position.

• Battery is not charged fully.

• Battery terminals are poorly connected.

• Defective internal wiring in connector

• Defective safety switch of seat

• Broken starter switch

• Broken starter motor

• Cock of fuel strainer is closed.

• No fuel

• Water trapped in fuel

• Air trapped in fuel

• Clogged fuel hoses

• Clogged fuel strainer

• Slow cranking speed

• Insufficient pre-heating
• Throttle lever is in low speed (

) position.

• Too high engine oil viscosity

• Clogged air-cleaner

• Insufficient compression

• Incorrect injection timing

• Clogged injection nozzles

• The engine hood is not closed.

• Air trapped in fuel system

• Improper earthing

• Clogged fuel strainer

• Leaking fuel system

• Defective injection pump

• Too low engine oil level

• Engine is overheated.

• Coolant temperature does not rise.

• Defective injection pump

Remedies

• Depress it fully.

• Turn it to OFF position.

• Charge it.

• Clean the terminal posts and con-

nect them securely.

• Rewire.

• Consult your dealer.

• Open it.

• Replenish with fuel.

• Drain trapped water from fuel

strainer.

• Bleed injection pump.

• Clean fuel hose inside.

• Wash or replace it.

• Charge battery.

• Preheat for specified time.

• Shift it to high speed position.

• Replace it with one of lower vis-

cosity.

• Clean element.

• Consult your dealer.

• Close the engine food securely.

• Locate cause of air-trapping and

bleed system of air.

• Polish earthing points and re-con-

nect.

• Clean or replace it.

• Tighten joints securely or replace

damaged hose.

• Consult your dealer.

• Add oil to upper limit.

• Consult your dealer.

Summary of Contents for SF310





























































































Search results

Summary of Contents for SF310

Reviews:

Iseki SF310, Operator'S Manual, Page: 77 / 92

Search results

Summary of Contents for SF310

Reviews: