background image

Layout and Installation Considerations

Page 4

http://support.timeips.com  316.264.1600

TimeIPS

TimeIPS

 Network Clock

Employee 

Identification 

device

Power Source 

(Wall outlet)

Overall Installation Notes:

Installation of the TimeIPS system normally takes less than an hour. If you have 
multiple locations, a complex network or are not familiar with networking, installation 
may take longer. Our Technical Support department is available to assist if you have 
installation questions.

All TimeIPS servers and clocks should be installed in an indoor location, out of direct 
sunlight, meeting the temperature requirements listed on the back cover of this guide.

Possible Primary and Remote Facility Installation

Existing Ethernet

10/100 Network

Existing Ethernet

10/100 Network

Primary 
Facility

Administration

and

Reporting

(Password 
Protected)

Side Door

F

ro

n

D

o

o

r

B

a

c

k

 D

o

o

r

Remote 
Facility

Typical Door Area Installation 
with Network Clock

TimeIPS Network 
Clock

Any PC with a web 
browser

Permanent network 
connection

Permanent or 
temporary network 
connection

TimeIPS 

Server

Network cable 

connected to 

your LAN

Summary of Contents for IPS265T

















Reviews: