INVENTOR DRVI32-09WF, User Manual

Page: 14 / 36

Indoor Unit Installation
[ Left Left-rear piping ]
Fitting of the Mounting Plate and Positioning of the wall Hole
In case of left side piping, cut away, with a nipper, the lid for left
piping.
In case of left-rear piping, bend the pipes according to the piping
direction to the mark of hole for left-rear piping which is marked on
heat insulation materials.
When the mounting plate is first fixed
1. Carry out, based on the neighboring pillars or lintels, a proper leveling
for the plate to be fixed against the wall, then temporarily fasten the plate
with one steel nail.
Indoor/outdoor electric cable
Heat insulation
material Piping
Lid for right
Pipe supporting
piping
Drain hose
plate
Lid for left piping
Lid for under piping pipe
Fix with adhesive tape
Indoor/outdoor electric cable and drain hose must be bound with
efrigerant piping by protecting tape.
[ Other direction piping ]
Cut away, with a nipper, the lid for piping according to the piping
direction and then bend the pipe according to theposition of wall
hole. When bending, be careful not to crash pipes.
Connect beforehand the indoor/outdoor electric cable, and then
pull out the connected to the heat insulation of connecting part
specially.
Fixing the indoor unit body
Hang surely the unit body onto the upper
notches of the mounting plate. Move the body
from side to side to verify its secure fixing.
In order to fix the body onto the mounting
plate,hold up the body aslant from the
underside and then put it down perpendicularly.
mounting plate
When the mounting plate is fixed side bar and lintel
Unloading of indoor unit body
Fix to side bar and lintel a mounting bar, Which is separately sold, and
then fasten the plate to the fixed mounting bar.
Refer to the previous article, “ When the mounting plate is fi rst fixed “,
for the position of wall hole.
When you unload the indoor unit,please use your hand to arise
the body to leave agraffe,then lift the bottom of the body outward
slightly and lift the unit aslant until it leaves the mounting plate.
Making a Hole on the Wall and Fitting the Piping Hole Cover
Make a hole of 60 mm in diameter, slightly descending to outside the wall
Install piping hole cover and seal it off with putty after installation
Wall hole
agraffe mounting plate
Ø60mm
Connecting the indoor/outdoor Electric Cable
Indoor side
Outdoor side
Thickness of wall
(Section of wall hole)
G Piping hole pipe
Removing the wiring cover
Installation of the Indoor Unit
Remove terminal cover at right bottom corner of
indoor unit, then take off wiring cover by removing
its screws.
Drawing of pipe
[ Rear piping ]
Draw pipes and the drain hose, then fasten them with the adhesive tape
1. Insert the drain hose into the dent of heat insulation materials of
indoor unit.
2. Insert the indoor/outdoor electric cable from backside of indoor
unit,and pull it out on the front side, then connect them.
3. Coat the flaring seal face with refrigerant oil and connect pipes.
Cover the connection part with heat insulation materials closely,
and make sure fixing with adhesive tape
2. Make sure once more the proper level of the plate, by hanging a thread
a h ti w weight from the central top of the plate, then fasten securely the
plate with the attachment steel nail.
3. Find the wall hole location A/C using a measuring tape
0 6 = B= B
0 6 = B= B
50mm
A=135mm
C=50mm
DRVI32-09WF
DRVI32-12WF
B= 60mm
B= 60mm
A=170mm
C=120mm
DRVI32-18WF
0 6 = B= B = B= B 0 6
A=100mm
C=110mm
DRVI32-24WF
40mm
30mm
10mm
10mm
30mm
40mm
Pay attention to the following points before installation of machine:
1. Take out cushion blocks on the left
and right angle beads as shown in
the following Figure.
t r e d n u s t e k s a g 2 e v o m e R .. 2
cross-flow fan.
u t c a rf f o e c a fr u s e h t n o r r u b e h t n a e l C .. 3
to avoid the power wire from being scratched after removing the
virtual opening of the outgoing
line slot on the case by
hands in indoor
power-on process.