background image

SPECIAL NOTES

Part No. 1110546

3

Tracer® EX2

SPECIAL NOTES

Signal

 

words

 

are

 

used

 

in

 

this

 

manual

 

and

 

apply

 

to

 

hazards

 

or

 

unsafe

 

practices

 

which

 

could

 

result

 

in

 

personal

 

injury

 

or

 

property

 

damage.

 

Refer

 

to

 

the

 

following

 

table

 

for

 

definitions

 

of

 

the

 

signal

 

words.

NOTICE

THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO CHANGE 

WITHOUT NOTICE.
WHEELCHAIR USER
As a manufacturer of wheelchairs, Invacare endeavors to supply a wide variety of wheelchairs to 

meet many needs of the end user. However, final selection of the type of wheelchair to be used 

by an individual rests solely with the user and his/her healthcare professional capable of making 

such a selection.
WHEELCHAIR TIE-DOWN RESTRAINTS AND SEAT POSITIONING STRAPS
Wheelchair users should NOT be transported in vehicles of any kind while in wheelchairs. As of 

this date, the Department of Transportation has not approved any tie-down systems for 

transportation of a user while in a wheelchair, in a moving vehicle of any type.
It is Invacare’s position that users of wheelchairs should be transferred into appropriate seating 

in vehicles for transportation and use be made of the restraints made available by the auto 

industry. Invacare cannot and does not recommend any wheelchair transportation systems.
ALWAYS wear your seat positioning strap. Inasmuch as the seat positioning strap is an option on 

this wheelchair (you may order with or without the seat positioning strap), Invacare strongly 

recommends ordering the seat positioning strap as an additional safeguard for the wheelchair 

user. The seat positioning strap is a positioning strap only. It is not designed for use as a safety 

device withstanding high stress loads such as auto or aircraft safety belts. If signs of wear appear, 

strap MUST be replaced IMMEDIATELY.
With regards to seat/chest positioning straps - it is the obligation of the DME dealer, therapists 

and other healthcare professionals to determine if a seat/chest positioning strap is required to 

ensure the safe operation of this equipment by the user. Serious injury can occur in the event of 

a fall from a wheelchair.

SIGNAL WORD

MEANING

DANGER

Danger indicates an imminently hazardous situation which, if not avoided, will result in death or serious 
injury.

WARNING

Warning indicates a potentially hazardous situation which, if not avoided, could result in death or serious 
injury.

CAUTION

Caution indicates a potentially hazardous situation which, if not avoided, may result in property damage, 
minor injury or both

Summary of Contents for TRACER EX2









































Reviews: