Invacare TRACER EX2 Owner'S Operator And Maintenance Manual Download Page 25

Page: 25 / 40

SECTION 5—ARMS

Part No. 1110546

Tracer® EX2

Removing/Installing Armrests

WARNING

Make sure the armrest release lever is in the locked position before using the wheelchair.

NOTE:

For

this

procedure,

refer

FIGURE 5.2

page

25.

Removing Armrest

Push

down

armrest

ensure

fully

seated

front

and

rear

sockets.

NOTE:

STEP

prevents

the

release

buttons

from

hanging

the

sockets

during

removal.

Press

the

armrest

release

button

the

front

and

rear

the

armrest.

While

pressing

the

armrest

release

buttons,

remove

the

armrest

from

the

arm

sockets

pulling

straight

up.

Installing Armrest

Position

the

armrest

just

above

the

front

and

rear

arm

sockets.

Push

arm

down

evenly

the

front

and

rear

until

the

front

and

rear

armrest

release

buttosn

snap

into

the

arm

sockets.

Ensure

armrest

locked

securely

the

arm

sockets

gently

lifting

up.

not

locked,

repeat

STEPS

‐

FIGURE 5.2

Removing/Installing Armrests

Armrest Release

Button

Armrest

Rear Arm

Socket

Front Arm

Socket

Armrest Release

Button

Summary of Contents for TRACER EX2









































Search results

Summary of Contents for TRACER EX2

Reviews:

Related manuals for TRACER EX2

Brands by name

Popular brands

Invacare TRACER EX2, Owner'S Operator And Maintenance Manual

Search results

Summary of Contents for TRACER EX2

Reviews:

Related manuals for TRACER EX2

Brands by name

Popular brands