background image

Components

3 Components

3.1

Main parts of the wheelchair

1

Headrest

2

Backrest

3

Armrest

4

Battery case (rear)

5

Drive wheel

6

Drive motor (with engaging lever)

7

Remote

8

Legrests

9

Caster wheel

10

Suspension, rear (both not visible in illustration, adjustable
for Storm4 X-plore only)

11

Suspension, center (Storm4 X-plore only)

3.2

Remotes

Your mobility device may be fitted with one of several different
remotes. For information on the different functions and how to
operate a particular remote, refer to its corresponding user manual
(enclosed).

3.3

The Lifter

The electric lifter is operated from the remote. Refer to the remote
manual for more information.

Information regarding operation of the lifter at
temperatures of less than 0 °C

Invacare mobility aids are fitted with safety mechanisms

that prevent capacity overload of the electronic
components. At operating temperatures below
freezing point this can, in particular, lead to the lifter
actuator being shut down after approx. 1 second
operating time.

The lifter can be raised or lowered gradually by

repeatedly operating the joystick. In many cases this
generates sufficient heat for the actuator to operate
as normal.

1529686-R

23

Summary of Contents for Storm4 True Track Plus















































































































Reviews: