manualshive.com logo in svg

Intracom WiBAS Connect, Commissioning Manual

Share
Download
Intracom WiBAS Connect Commissioning Manual Download Page 85

WiBAS OSDR-Hub & Terminal Station / WiBAS-Connect Terminal Station

 

Start Up & Commissioning Manual - Edition 5.1 

 

85 

Appendix A – LED Indications 

 

 

Radio unit LED 

status 

The LED at the bottom of radio unit provides visual indications of the system 
status: 

WiBAS

TM

-OSDR Hub: 

Status of STAT LED 

System Condition 

 

OFF 

Input power supply is absent. 

 

Stable ON, 

green

 

•

  Firmware upgrade 

•

  Power up 

 

Blinking 

green

 

firmware download 
Link in operation 

 

Stable ON, 

orange

 

Base station mute on 

 

Blinking 

orange

 

TS in ranging invitation 

 

Stable ON, 

red

 

•

  on power cord insertion (hot) 

•

  remove power cord 

 

 

WiBAS

TM

-OSDR Terminal Station: 

Status of STAT LED 

System Condition 

 

OFF 

Input power supply is absent. 

 

Stable ON, 

green

 

•

  Firmware upgrade 

•

  Power up 

 

Blinking 

green

 

•

  Firmware download 

•

 

Link in operation

 

 

Stable ON, 

orange

 

Admin down TS with rf link lock 

 

Stable ON, 

red

 

•

  on power cord insertion (hot) 

•

  remove power cord 

 

Blinking 

red

 

•

  BS mute on 

•

  TS with no DL lock 

 

 

Continued on next page

 

 

 

Summary of Contents for WiBAS Connect































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands