background image

195

PO

SAVE THESE INSTRUCTIONS

(195PO)  SAND FILTER PUMP  ENGLISH  7.5” X 10.3”  PANTONE 295U  06/29/2016

English

Page 15

Initial startup and operation:

Before operating, be sure that:

  •  All the hoses have been connected and tightened securely, and correct amount of filter sand 
    have been loaded.
  •  The entire system is connected to a grounding type receptacle protected by a ground-fault 
    circuit interrupter (GFCI) or residual current device (RCD). 

OPERATING INSTRUCTIONS (continued)

CAUTION

The filter control valve has a closed position. The pump should never be on when 
the valve is in the closed position. If the pump is operated with the valve closed, 
explosive situation could exist.  

1.

  Turn both plunger valve handles fully counter-clockwise until they stop. This opens the valves 

    to allow water to flow into the sand filter pump. With water flowing into sand filter pump, the 
    water pressure will allow the air trapped inside to escape from the air release valves 

(19)

    When all the air has escaped water will flow out of the valves 

(19)

. When this occurs gently 

    finger tighten the valves 

(19) 

in a clockwise direction. 

2. 

Ensure the drain/waste outlet on the 6-way valve is not 

    covered and directed to a proper draining receptacle.

3.

  Ensure the pump is off, depress the 6-way valve and turn 

    it to the “

BACKWASH

” position 

(see drawings 24 & 29)

.

   

IMPORTANT: To prevent damage to the 6-way valve, 

    always depress the valve handle before turning. 
    Always switch off pump before changing the 6-way 
   valve position. 
4.

  Switch on the pump 

(see drawing 30)

. Water is circulating 

    backward through the sand media and to waste/drain 
    outlet. Backwash until a clear flow of water is observed 
    in the waste/drain outlet or through the drain sediment  
   window.
   

NOTE:

 The initial backwash of the filter is recommended to 

    remove any impurities or fine sand particles in the sand 
   media.

R E T L I

F

E S N

I R

E

R

H

S

A

W

K

C

A

B

E

S

O

L

C

ET

S

A

W

26

R E T L I

F

E S N

I R

ET

AL

U

C

RI

C

E

R

H

S

A

W

K

C

A

B

E

S

O

L

C

27

R E T L I

F

ET

AL

U

C

RI

C

E

R

H

S

A

W

K

C

A

B

E

S

O

L

C

ET

S

A

W

28

29

1

2

30

TIMER

OFF

ON

Summary of Contents for SF60110-1

























Reviews: