manualshive.com logo in svg

Intex PureSpa Greywood Deluxe SB-HWF20, Owner'S Manual

Share
Download
Intex PureSpa Greywood Deluxe SB-HWF20 Owner'S Manual Download Page 21

352

A

S  AVE THESE INSTRUCTIONS

(352IO)  SPA  ENGLISH  7.5” X 10.3”  PANTONE 295U  09/18/2020

English

Page 21

LED CODE CHART

LED Reading

CAUSE

SOLUTION

E81

Transmission signal failure

•  Reset the RCD, restart all over again.
•  Place the control panel within 5 m (16 ft) of the 

control base unit.

•  Press and hold POWER button for 5 seconds to 

turn off  and charge the panel again.

•  If problem persists, contact Intex Service Center.

E90

No water fl ow

•  Turn off  and unplug the control unit.
•  Ensure the outlet cover grid is clean and free from 

obstructions.

•  Clean or replace the cartridge, see Maintenance 

and Storage section.

•  Ensure the in/outlet connections on the spa tub and 

fi lter pump are not blocked.

•  Keep the spa water properly sanitized to ensure a 

clean and unclogged fi lter cartridge.

•  If problem persists, contact Intex Service Center.

E94

Water temperature too low

•  If the ambient temperature is below 4°C (39°F), we 

recommend not to use the spa.

•  Turn off  and unplug the control unit, add some 

warm water to raise the spa water temperature 
above 5°C (41°F), then press the

 

 button to heat 

up the water to the desired temperature.

•  If problem persists, contact Intex Service center.

E95

Water temperature too high

•  Turn off  and unplug the control unit. When the water 

has cooled down, plug the RCD and restart all over 
again.

•  Turn the heater off , then press the fi lter and bubble 

buttons to lower the water temperature.

•  If problem persists, contact Intex Service Center.

E96

System Error

•  Turn off  and unplug the control unit. Plug the RCD 

and restart all over again.

•  If problem persists, contact Intex Service Center.

E97

Dry-fi re Protection

•  Contact Intex Service Center.

E99

Water temperature sensor broken •  Contact Intex Service Center.

END

After 72 hours of continuous 

heating operation, the pump will 

hibernate automatically. The rapid 

heating function is disabled.

•  Press the

 

 button to re-active the fi lter pump. 

BLANK

Control panel battery has no power 

or in “Power Saving Mode” waiting 

to be placed on the control base 

charging dock.

•  Press any button to reactivate the control panel.
•  Reset the RCD, restart all over again and charge 

the control panel again.

•  Make sure the surface between the back of the 

control panel and the control base charging dock is 
clean, dry and free of obstruction.

•  If problem persists, contact Intex Service Center.

Summary of Contents for PureSpa Greywood Deluxe SB-HWF20

































Reviews:

No comments

Brands by name

Popular brands

Load more brands