background image

352

A

S  AVE THESE INSTRUCTIONS

(352IO)  SPA  ENGLISH  7.5” X 10.3”  PANTONE 295U  09/18/2020

English

Page 14

SET UP (continued)

Spa Control Unit Installation

1.

  Connect the spa control unit to the spa tub 

(see drawing 10)

. Hand-tighten the connectors securely. Do 

not use tools to tighten.

 

NOTE:

 Never attach external accessories not supplied with the kit to the spa tub or control base unit, as 

this will void the warranty.

2.

  Replace the control base side covers

 (4)

 

(see drawing 11)

.

 

  CAUTION: 

Do not sit, lean, cover or place any objects over the spa control unit.

3.

  Attach the fi lter cartridge housing assembly to the inside of the spa 

tub outlet grid (lower position) 

(see drawing 12)

.

 

Infl ate the spa tub 

fi rst before installing fi lter pump fi ttings. 

4.

  Before fi lling with water ensure the bottom drain valve caps are 

securely closed on the inside and outside.

5.

  Fill the spa tub with freshwater to a level between MIN and MAX 

marked on the inside of the spa wall. Do not over fi ll the spa. 

 

Never  move the spa tub with water inside and/or with the control 

base attached to the spa as the spa or control base may be 

damaged. 

 

WARNING: 

Never pour water with a temperature higher than 

  40°C (104°F) into the spa directly. It is recommended to fi ll the 

spa tub with lukewarm water for quick heating and energy saving.

6.

  Place the spa cover and spa air bladder (pre-installed in spa cover) 

 

over the spa tub, and make sure the spa cover buckles are locked 

using the key provided after pulling the buckled straps tight.

 

IMPORTANT:

 Inspect the spa cover regularly for leak, premature wear and tear or deterioration. Never 

 

use a damaged spa cover. 

7.

  Ensure that the spa base is plugged into a properly located and sized electrical outlet and press the 

 

button to turn on the control panel. Press the 

 button on the control panel to activate the heater, see “Spa 

Control Panel” operation section.

Spa Cover

The attachment buckles of the cover are locking buckles. Two keys are provided in the plastic bag with the 

manual and other accessories. Each buckle is marked with “locked” and “unlocked” symbols for easy operation: 

put the key into the slot on the buckle and turn it to the appropriate position to lock or unlock the buckle 

respectively. 

To assure safety from unauthorized access, always put the cover on when spa is not in use and lock all 

buckles. Always keep the keys out of reach of children. In case you misplace the keys, you can use any similar 

size fl at screwdriver to lock or unlock the buckles.

When the spa is being used, the cover should be placed in a clean, dry area, otherwise it can pick up dirt and 

bacteria. Covers should not be put on wooden tables or wooden decking because of the risk of bleaching the 

wood. A cover lifter, dedicated support or similar device, is recommended for ensuring that the cover, mostly its 

side facing the water, does not come into contact with the ground or any other dirty surfaces.

11

10

12

Summary of Contents for PureSpa Greywood Deluxe SB-HWF20

































Reviews: