Intex Hydro Flow SM24101 Owner'S Manual Download Page 2

(303PO)  MODEL SM24101 SWIMMING MACHINE  ENGLISH  7.5” X 10.3”  PANTONE 295U  02/21/2017

303

PO

    

SAVE THESE INSTRUCTIONS

English

Page 2

Warnings

..................................................................................... 

3

 

Parts Reference

.......................................................................... 

4-5

 

Product Specification

................................................................ 

6

Setup Instructions

...................................................................... 

6-13

 

Operating Instructions

............................................................... 

14-15 

Maintenance

...............................................................................  

15

Internal Parts Replacements

.....................................................

 16-17

Troubleshooting Guide

..............................................................

 18-19

Limited Warranty

......................................................................... 

20

TABLE OF CONTENTS

Operation is subject to the following two conditions: (1) this device may not cause interference, 
and (2) this device must accept any interference, including interference that may cause 
undesired operation of the device.

Changes or modifications not expressly approved by the party responsible for compliance could 
void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for Class B digital device, 
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates, uses and can 
radiate radio frequency energy and, if not installed and used in accordance with the instructions, 
may cause harmful interference to radio communications. However, there is no guarantee that 
interference will not occur in a particular installation. If this equipment does cause harmful 
interference to radio or television reception, which can be determined by turning the equipment 
off and on, the user is encouraged to try to correct the interference by one or more of the 
following measures:
•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and the receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the 
  receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.

Summary of Contents for Hydro Flow SM24101





















Reviews: