20
WARNING!
Before performing any maintenance to your treadmill, always unplug the power cord from the surge
protector.
CLEANING:
Routine cleaning of your TREADMILL will extend the life of your treadmill.
WARNING! To prevent electrical shock, be sure the power to the treadmill is OFF and the unit is unplugged from
the wall electrical outlet before attempting any cleaning or maintenance.
AFTER EACH WORKOUT
: Wipe off the console and other treadmill surfaces with a clean, water dampened soft
cloth to remove excess perspiration. USE NO CHEMICALS.
WEEKLY:
Use of a treadmill mat is recommended for ease of cleaning. Dirt from your shoes contacts the belt and
eventually ends up underneath the treadmill. Vacuum underneath the treadmill once a week.
DECK LUBRICATION:
The walking belt has been pre-lubricated at the factory. However, it is recommended that
the walking board be checked periodically for lubrication to ensure optimal treadmill performance.
Every 10 days or 10 hours of operation, lift the sides of the walking belt and feel the top surface of the walking
board as far under as you can reach. If you feel signs of silicone, no further lubrication is required.
If it feels dry to the touch, lubrication is needed. Ask your retailer or call Service line for the type of silicone.
TO APPLY LUBRICANT TO THE WALKING BOARD
1) Position the walking belt so that the seam is located on top and in the center of the center of the
walking board.
2) Insert the spray nozzle into the spray head of the lubricant can.
3) While lifting the side of the walking belt, position the spray nozzle between the walking belt and the
board approximately 10cm from the front of the treadmill. Apply the silicone spray to the walking board,
moving from the front of the treadmill to the rear. Repeat this on the other side of the belt.
Spray approximately 4 seconds on each side.
4) Allow the silicone to 'set' for one minute before using the treadmill.
WARNING:
Do not over-lubricate the walking board. Excess lubricant should be wiped off with a clean towel.
Summary of Contents for ENERGETICS PR 8.9
