P/N 146667999-
1 (ML) • REV G • ISS 19AUG19
7 / 52
Green mode
When SW1-5 is set to Remote on, the radar is switched off
during the day mode (with no WT) to reduce current
consumption. The detector is then operating in PIR only mode.
Note:
The Day/night line must be connected to the control
panel for this mode to work.
Alarm memory
When SW1-5 is set to Remote on, alarms that occurred during
the night mode are stored in the detector memory. They are
indicated by flashing red LED when the unit switches to day
mode (walk test disabled). The memory is cleared when the
detector switches back to the night mode.
Note:
Set SW1-6 to Off to prevent showing the alarm memory
on the LEDs. See
LEDs and outputs
To enable LEDs functionality, set SW1-6 to On, otherwise
LEDs are disabled in any condition. See
page 6 for more details.
Table 6: LEDs and outputs
Status
Red
LED
Yellow
LED
Alarm
relay
Fault
relay
To reset
Start up
Closed
Closed Automatically
after 60 s
Low voltage
Open
Open
Apply correct
voltage
PIR intruder
alarm
Closed
Closed
Microwave
intruder alarm
Closed
Closed
Dual motion
intruder alarm
Open
Closed Automatically
after 3 s
Dual Alarm
Memory
Closed
Closed Switch to the
night mode
AM alarm
Depends
on SW2-4
Open
Depends on
SW2-3
Technical fault
Closed
Open
Successful walk
test
Continuously ON
Normal blinking (1 Hz)
Specifications
Detector technology
Dual+AM
Range
10, 12, 14, 16 m selectable via
SW1-1 and SW1-2
Viewing angle
78 degrees
PIR optics
9 high-density mirror curtains
Microwave frequency
5.8 GHz
Max microwave output at 1 m
0.003 μW/cm²
Memory function
Yes
Input power
9 to 15 V
(12 V nominal)
Peak-to-peak ripple immunity
2 V (at 12 V
)
Detector start-up time
60 s
Current consumption
10 to 22 mA (11 mA nom.)
Mounting height
2.0 to 3.0 m (6.60 to 9.84 ft.)
Target speed range:
DDV1016AM
0.2 to 3.0 m/s (8 in./s to 10 ft./s)
DDV1016AM-D
0.1 to 4.0 m/s (4 in./s to 13 ft./s)
Alarm (NC) / Tamper relay
characteristic
80 mA 30 V
, Form A
Fault relay characteristic
80 mA 30 V
, Form A
Alarm time
3 s
Operating temperature
−10 to +55°C (14 to 130°F)
Relative humidity
95% max., noncondensing
Weight
120 g
Dimensions (H x W x D)
126 × 63 × 50 mm
IP/IK rating
IP30 IK04
Pry-off tamper
Yes
Regulatory information
Manufacturer
UTC Fire & Security Americas Corporation, Inc.
3211 Progress Drive, Lincolnton, NC, 28092, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Netherlands
Product warnings
and disclaimers
THESE PRODUCTS ARE INTENDED FOR SALE
TO AND INSTALLATION BY QUALIFIED
PROFESSIONALS. UTC FIRE & SECURITY
CANNOT PROVIDE ANY ASSURANCE THAT
ANY PERSON OR ENTITY BUYING ITS
PRODUCTS, INCLUDING ANY
“AUTHORIZED
DEALER
” OR “AUTHORIZED RESELLER”, IS
PROPERLY TRAINED OR EXPERIENCED TO
CORRECTLY INSTALL FIRE AND SECURITY
RELATED PRODUCTS.
For more information on warranty disclaimers and
product safety information, please check
https://firesecurityproducts.com/policy/product-
warning/ or scan the QR code.
Certification
European Union
directives
UTC Fire & Security hereby declares that this
device is in compliance with the applicable
requirements and provisions of all applicable
rules and regulations, including but not limited to
the Directive 2014/53/EU. For more information
see: www.utcfssecurityproducts.eu
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
www.recyclethis.info
Contact information
www.utcfireandsecurity.com or www.interlogix.com.
For customer support, see www.utcfssecurityproducts.eu
