Intergraph Fibre Channel User Manual Download Page 47

Page: 47 / 84

Troubleshooting

4.9.2.2

Inserting the Module

Install the module by sliding into the correct bay (1/1 at front or 3/1 at rear) ensuring the module has docked with

the connector and the retention clip has engaged with the chassis. (

Figure 4–5

)

Caution

TheESI/Ops panel module variants are not interchangeable, a front mountied module cannote be
installed in the rear mounting position and vice versa.

4.10 List of Spare Parts and Ancillary Items

The following replaceable parts are available for the SS-1200-FCAL subsystem:

• Chassis (including Backplane)

• 19 inch rack mounting rail kit

• AC Power Supply/Cooling Module

• ESI/Ops Panel module (Front facing or Rear facing)

• Drive Carrier Module

• Front dummy fascia plates

• I/O Module

• Blank plates (1x1, 1x2 or 1x3)

• External FC-AL Signal Cables:

• (Country specific) power cords

• Tri-furcated power cords

• Keys for ESI/Ops Panel and Drive Carrier modules.

• All documentation

Figure 4–5

Installing an ESI/OpsPanel Module (Rear Mounting)

Summary of Contents for Fibre Channel





















































































Search results

Summary of Contents for Fibre Channel

Reviews:

Intergraph Fibre Channel, User Manual, Page: 47 / 84

Search results

Summary of Contents for Fibre Channel

Reviews: