manualshive.com logo in svg

Intergraph Fibre Channel, User Manual, Page: 1 / 84

Share
Download
Intergraph Fibre Channel User Manual Download Page 1

Fibre Channel User’s Guide

DHAV04500

Congratulations on purchasing Intergraph’s state-of-the-art Fibre Channel storage solution.  If
you are a manager, you will find this solution gives you matchless performance in a cost-
competitive storage device.  If you are a technician, you will find this solution easy to install,
reliable, and easy to maintain.  If you are a user, you will enjoy fast access to a vast expanse of
storage space.

Using This Document

The Fibre Channel User’s Guide contains all the information you need to install and use your
Fibre Channel disk array.  This document is organized as follows:

u 

SS-1200 FCAL Rack Installation and User Guide describes how to install, configure, and
connect the Fibre Channel enclosure to your system, and how to use and maintain it.

u 

SS-1200 FCAL LRC Input/Output Module Installation Guide describes how to install the
Fibre Channel Arbitrated Loop (FCAL) Loop Resiliency Circuit (LRC) input/output (I/O)
modules in the Fibre Channel enclosure.

u 

SS-1200 FCAL Drive Carrier Module Installation Guide describes how to install the FCAL
drive carrier modules in the Fibre Channel enclosure.

Before You Begin

CAUTION

To protect the Fibre Channel enclosure and related equipment from electrostatic
discharge, wear an anti-static wrist strap when setting up or reconfiguring the
enclosure.

WARNING

To avoid damage to the enclosure’s power supply, set the voltage range
switch on the power supply to the proper AC line voltage for your location
(115 V or 220 V) before you connect the power cord and turn on power to
the enclosure.

Customer Support

Intergraph Computer Systems offers an assortment of customer support options.

u 

Intergraph Computer Systems provides a variety of hardware services for Intergraph and
third-party equipment.  Services include warranty upgrades, repair depot service, on-site
hardware maintenance, system administration, and network consulting.  Hardware purchased
from Intergraph Computer Systems includes a factory warranty ranging from 30 days to three
years.  A detailed warranty description is available on the World Wide Web; see the Support
pages at http://www.intergraph.com/ics .

u 

Intergraph Computer Systems provides complimentary software support for 30 or 90 days
following shipment of a hardware or software product.  This includes World Wide Web
access, Intergraph Bulletin Board Service access, FAXLink service, and telephone (Help
Desk) support.  At the end of the complimentary support period, you can purchase other
levels of software support.

Summary of Contents for Fibre Channel





















































































Reviews:

No comments