background image

BYOS-IM  Rev. 08/15  (SBK-BYOS INSTAL)

B Y O S 1

S L I D E   S Y S T E M

( B U I L D   Y O U R   O W N   S L I D E )

Assembly & Installation Instructions

Visit inter-fab.com to view our installation help video. 

(Video does NOT replace installation instructions.) 

I N T E R - F A B ,   I N C .   3 0 5 0   S .   A L V E R N O N   W AY   •   T U C S O N ,   A Z   8 5 7 1 3

5 2 0 . 7 9 0 . 7 0 4 0   •   8 0 0 . 7 3 7 . 5 3 8 6   •   F A X   5 2 0 . 7 9 0 . 7 1 2 7   •   i n t e r - f a b . c o m

IMPORTANT INSTALLATION INFORMATION

The installation of this product should be done only by a licensed and professional installer.  Installation should
be done strictly in conformance with all local building codes, electrical codes and other building and safety laws
and regulations. Among other things, your installer should carefully analyze the need to bond the product to
prevent an electrical hazard. Failure to properly install this product could result in a dangerous condition,
including but not limited to electrical or structural hazards. Inter-Fab, Inc. disclaims all liability arising from the
installation and the user assumes all risk associated with the installation.  

WARNING

Summary of Contents for BYOS 1 SLIDE SYSTEM





















Reviews: