background image

at InTense, we have one goal -  
to provide the ride of your life //

Our team of designers, engineers and product experts are focused on 
one thing every day: your experience on the bike. We build bikes that are 
as thrilling to look at as they are to ride, and we build them for the select 
few of you who understand the difference and refuse to settle for anything 
else. From the early days of INTENSE, when founder Jeff Steber worked 
alone in his garage to today, where a crew of talented people work in a 
Temecula, CA factory, INTENSE has been a brand built on passion by 
forward thinkers who, even today, love nothing more than to throw a leg 
over a sweet bike and head out for a rip. We’re so glad you’ve joined us. 
Welcome to INTENSE, enjoy your experience.

the sniper T //

The Sniper T is a dedicated pedaling machine with an uptick in rear wheel 
travel for your favorite descent. We’ve reinforced the rear triangle for added 
strength and stability but also, to further separate it from its shorter travel, 
XC sibling. This is not a “rigid” race bike…with the efficiency of the 29” 
wheels, modern geometry and proven suspension kinematics, any trail is 
a blast on the Sniper T.   

register your bike // 

www.intensecycles.com/warranty-card/

t e c h n i c a l   a s s i s t a n c e

techcent[email protected] 

 

951-307-9211

Welcome to 

the family

2

 

// 

s n i p e r   T   m a n u a l

Summary of Contents for Sniper T

























Reviews: