Intelligent Energy FCPM User Manual Download

Page: 33 / 36

12 Appendix

Flag Code

Tag

Description

00000002

DisableExternalOutputCheck

Digital output tell-back not the same as set

00000001

EnableStackOutputCheck

Digital output tell-back not the same as set

80000000

StackTxSensor1OverTemperature

Above temperature limit (>58°C)

40000000

StackTxSensor2OverTemperature

Above temperature limit (>58°C)

20000000

NegativeEndPlateTxSensorOverTemperature Above temperature limit (>58°C)

10000000

PositiveEndPlateTxSensorOverTemperature Above temperature limit (>58°C)

08000000

AirInletTxSensorOverTemperature

Above temperature limit (>58°C)

04000000

Rail5V1EnableOutputCheck

Digital output tell-back not the same as set

02000000

Rail5V2EnableOutputCheck

Digital output tell-back not the same as set

01000000

Rail12V1EnableOutputCheck

Digital output tell-back not the same as set

00800000

Rail12V2EnableOutputCheck

Digital output tell-back not the same as set

00400000

StackOverVoltage

Stack voltage above threshold (>80V)

00200000

StackUnderVoltage

Stack voltage below threshold when fuel on and
not POC (<36V)

00100000

StackOutputOverCurrent

Stack output current above DCDC input max
current (>40A)

00080000

UnexpectedStackOutputCurrent

Stack output current above threshold when the
DCDC is not enabled (>3A)

00040000

FanPulseOverCurrent

Current to POC load resistor above threshold
(>250A)

00020000

UnexpectedFanPulseCurrent

POC load resistor current above threshold when
the load resistor is not enabled (>3A)

00010000

LoadDcdcOutputOverVoltage

Output voltage is above threshold (>85A)

00008000

LoadDcdcOutputControlLost

Output voltage is significantly above set point
(>3A than setpoint)

00004000

LoadDcdc1OuputCheck

SPM 1 Output voltage below setpoint
(difference >2V) AND output current is
below limit (difference >3A). Implies a
DCDC output power fault.

00002000

LoadDcdc2OuputCheck

SPM2 Output voltage below setpoint
(difference >2V) AND output current is
below limit (difference >3A). Implies a
DCDC output power fault.

00001000

BalanceOfPlantUVWarningA

BOP voltage below limit (<35V)

00000800

BalanceOfPlantUVDenyStart

BOP Under Voltage before start command (<35V)
(this will deny start)

00000400

BalanceOfPlantUVWarningB

BOP Under Voltage warning flag (<30V)

00000200

FanEscTelemetryCrcFault

Fan ESC telemetry fault

00000100

FanEscTelemetryNoMessages

No communications from the fan ESC

00000080

HighFanPulseCurrentAbort

POC aborted due to higher than expected
current (<45V)

00000040

SafetyPairFault

Both safety voltages lost from SPM while SPM
is operating

Summary of Contents for FCPM





































Search results

Summary of Contents for FCPM

Reviews:

Related manuals for FCPM

Brands by name

Popular brands

Intelligent Energy FCPM, User Manual

Search results

Summary of Contents for FCPM

Reviews:

Related manuals for FCPM

Brands by name

Popular brands