Intel VIA K8T800 User Manual Download Page 54

Page: 54 / 92

BIOS

Page 4-20

4-6 PNP/PCI Configuration

This page lets the user to modify the PCI IRQ signals when various PCI cards are
inserted.

WARNING: Conflicting IRQs may cause system unable to locate certain devices.

Figure 7: PNP/PCI Configuration Setup

PNP OS Installed

Select Yes if you have a PNP OS installed on your system. The default is No.
Options: Yes, No.

Reset Configuration Data

This setting allows you to clear ESCD data. The default is Disabled

Disabled

: Normal Setting.

Enabled

: If you have ever plugged Legacy cards to the system and their data

remains recorded into ESCD (Extended System Configuration Data), you
can set this field to Enabled in order to clear ESCD data.

Resources Controlled By

Determines what controls system PNP/PCI resources. The default is Auto (ESCD).

Manual

: PNP Cards resources are controlled manually. The IRQ Resources field

becomes available and you can set which IRQ-X and DMA-X are
assigned to PCI and onboard devices.

Auto

BIOS assigns the interrupt resource automatically.

Summary of Contents for VIA K8T800





























































































Search results

Summary of Contents for VIA K8T800

Reviews:

Related manuals for VIA K8T800

Brands by name

Popular brands

Intel VIA K8T800, User Manual

Search results

Summary of Contents for VIA K8T800

Reviews:

Related manuals for VIA K8T800

Brands by name

Popular brands